2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The throttle position sensor is mounted on the diesel throttle body assembly and detects the opening angle of the throttle valve. This sensor is an electronic sensor and uses Hall-effect elements.
When the throttle valve is fully closed, a voltage of approximately 0.7 V is applied to terminal VLU of the ECM. The voltage applied to terminal VLU of the ECM increases in proportion to the opening angle of the throttle valve and becomes approximately 3.5 to 4.0 V when the throttle valve is fully opened.
The ECM determines the vehicle driving conditions from the signals input to its VLU terminal. The data is one of the pieces of information used for EGR control, etc.
A128639E01
P0122 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Engine switch on (IG) for 3 seconds
Throttle position sensor output (VLU) is below 0.2 V for 3 seconds (1 trip detection logic).
  1. Throttle position sensor
  2. Open or short in VLU circuit
  3. Open in VC circuit
  4. ECM
P0123 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Engine switch on (IG) for 3 seconds
Throttle position sensor output (VLU) is higher than 4.8 V for 3 seconds (1 trip detection logic).
  1. Throttle position sensor
  2. Open in E2 circuit
  3. VC and VLU circuits are short-circuited
  4. ECM

HINT:
If DTC P0122 and/or P0123 is stored, the following symptoms may appear:

  1. - Intake booming noise
  2. - Black smoke
  3. - Lack of power
  4. - Vibration at engine stop
  5. - Turbo overspeed, turbo damage

MONITOR DESCRIPTION

When the output voltage of the throttle position sensor deviates from the normal operating range (between 0.2 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.
G037166E09

WIRING DIAGRAM

A221590E01

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  3. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
  1. Disconnect the throttle position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C73-1 (VC) - C91-8 (VCVL)
    Always
    Below 1 Ω
    C73-3 (VTA) - C91-3 (VLU)
    Always
    Below 1 Ω
    C73-2 (E2) - C91-9 (EVLU)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C73-1 (VC) or C91-8 (VCVL) - Body ground
    Always
    10 kΩ or higher
    C73-3 (VTA) or C91-3 (VLU) - Body ground
    Always
    10 kΩ or higher
    C73-2 (E2) or C91-9 (EVLU) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the throttle position sensor connector.

  1. Reconnect the ECM connector.



NG
Go to step 6
OK


2. CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)

  1. C129053E11
    Disconnect the throttle position sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C73-1 (VC) - C73-2 (E2)
    Engine switch on (IG)
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Throttle Position Sensor)

  1. Reconnect the throttle position sensor connector.



NG
Go to step 5
OK


3. REPLACE DIESEL THROTTLE BODY ASSEMBLY
  1. Replace the diesel throttle body assembly (Click here).


NEXT


4. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the intelligent tester on.

  1. Clear the DTCs (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Actual Throttle position.

  1. Check the movement of the throttle valve when idling the engine after starting it from engine switch on (IG).

    OK:
    Condition
    Tester Display
    Engine switch on (IG)
    -5 to 5%
    Idling
    0 to 93%



OK
END

NG
Go to step 5
5. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 7
6. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG) for 3 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END


← P011C Charge Air Temperature/Intake Air Temperature Correlation (Bank 1) (from Aug 2014)P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input (+ P0123) (from Aug 2014) →