P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The ECM opens and closes the throttle valve using a rotary solenoid type actuator. Due to the opening and closing of the valve, the exhaust gas recirculation volume can be properly controlled. Also, engine vibration and noise will be reduced by closing the valve when the engine is stopped.| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state. |
Target and actual opening angle of the throttle valve differs for approximately 20 seconds. (1 trip detection logic) |
|
| The throttle motor activation duty exceeds the threshold for 0.5 seconds a certain number of times (40 seconds or more). (1 trip detection logic) |
| DTC No. |
Data List |
| P0488 |
|
| Condition |
Throttle Valve Position |
| Moment when accelerator pedal is depressed further or released at 3000 rpm |
Throttle valve opening angle varies smoothly |
MONITOR DESCRIPTION
The ECM opens and closes the throttle valve by adjusting the current flowing to the rotary solenoid with a duty ratio. If the throttle valve does not move smoothly or is stuck, the duty ratio used during valve movement control increases or decreases greatly. The ECM will determine that the throttle valve is malfunctioning and illuminate the MIL.

WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
- After replacing an injector assembly, the ECM needs registration (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- HINT:
- Although the DTC titles say exhaust gas recirculation throttle position control Range / Performance, these DTCs relate to the throttle valve
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
- Although the DTC titles say exhaust gas recirculation throttle position control Range / Performance, these DTCs relate to the throttle valve
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DIESEL THROTTLE TARGET ANGLE) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Diesel Throttle Target Angle.
When changing the Active Test continuously value to 0, 30, 60, 90, 60, 30 and 0%, check that Actual Throttle Position smoothly changes to the set opening angle.
- OK:
- Value smoothly changes to set opening angle.
|
|
||||
|
|
||||
| 2. CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR POWER SOURCE) |
Disconnect the throttle control motor connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
C74-2 (B) - Body ground
Engine switch on (IG)
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Throttle Control Motor)
Reconnect the throttle control motor connector.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT) |
Disconnect the throttle control motor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
C74-3 (RSC) - Body ground
Always
Below 1 Ω
Reconnect the throttle control motor connector.
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM) |
Disconnect the throttle control motor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
C74-1 (RSO) - C92-15 (LUSL)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
C74-1 (RSO) or C92-15 (LUSL) - Body ground
Always
10 kΩ or higher
Reconnect the throttle control motor connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 5. REMOVE DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY) |
Visually check for deposits in the diesel throttle body. If there are deposits, clean the diesel throttle body.
| NEXT | |
| 6. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DIESEL THROTTLE TARGET ANGLE) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Diesel Throttle Target Angle.
When changing the Active Test continuously value to 0, 30, 60, 90, 60, 30 and 0%, check that Actual Throttle Position smoothly changes to the set opening angle.
- OK:
- Value smoothly changes to set opening angle.
|
|
||||
|
|
||||
| 7. REPLACE DIESEL THROTTLE BODY ASSEMBLY |
Replace the diesel throttle body assembly (Click here).
| NEXT | |
| 8. CHECK WHETHER DTC OUTPUT RECURS |
Clear the DTCs (Click here).
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester on.
Start the engine.
Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm and lower it.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
Result Result
Proceed to
P0488 is output
A
No DTC is output
B
|
|
||||
| A | |
| 9. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 10. REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE CONTROL MOTOR - BATTERY) |
Repair or replace the harness or connector.
|
|
||||
| 11. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 12. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the engine switch off.
Start the engine.
Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm, and then lower it.
Confirm that the DTC is not output again.
- HINT:
- Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P0488.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm again, and then idle the engine for 5 minutes.
| NEXT | ||
| ||
