2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P2454 Diesel Particulate Filter Pressure Sensor "A" Circuit Low

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

HINT:
  1. For more information on the differential pressure sensor assembly and Diesel Particulate Filter (DPF), refer to the following procedures (Click here).
  2. If P2454 and/or P2455 is present, refer to the DTC chart for DPF system (Click here).

A128654E03
The two sensing chambers of the differential pressure sensor assembly are mounted to monitor the pressure before and after the DPF catalytic converter. The sensor itself is not located on the engine assembly in order to reduce the influence of vibration.
The ECM compares the exhaust gas pressure before and after the DPF catalytic converter by monitoring the pressure using the upstream and downstream sensing chambers of the differential pressure sensor assembly. If the difference in pressure exceeds a predetermined level, the ECM judges that the catalytic converter is clogged with particulate matter (PM). When the ECM judges that a partially clogged condition exists, the ECM begins to perform PM forced regeneration.
When the output voltage of the sensor deviates from the normal operating range, the ECM interprets this as a malfunction of the sensor circuit, and sets DTC P2454 or P2455, and illuminates the MIL.

HINT:
If the vacuum hoses of the differential pressure sensor assembly are incorrectly connected (crossed), the ECM interprets this as an abnormal pressure difference, DTC P2453 (Diesel Particulate Filter Pressure Sensor "A" Circuit Range/Performance) is stored and the MIL illuminates.

P2454 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Engine switch on (IG) for 5 seconds
differential pressure sensor assembly output voltage is below 0.4 V for 3 seconds or more.
(1 trip detection logic)
  1. Open or short in differential pressure sensor assembly circuit
  2. Incorrect Differential pressure sensor Assembly hose routing
  3. Differential pressure sensor Assembly
  4. ECM
P2455 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Engine switch on (IG) for 5 seconds
differential pressure sensor assembly output voltage is higher than 4.8 V for 3 seconds or more.
(1 trip detection logic)
  1. Open or short in differential pressure sensor assembly circuit
  2. Incorrect Differential pressure sensor Assembly hose routing
  3. Differential pressure sensor Assembly
  4. ECM
Related Data List 
DTC No.
Data List
P2454
DPF Differential Pressure
P2455

HINT:
  1. DTC P2453 (Diesel Particulate Filter Pressure Sensor "A" Circuit Range / Performance) will be stored if there is incorrect vacuum hose routing to the differential pressure sensor assembly.
  2. After confirming DTC P2454 and P2455, check the differential pressure in the "Powertrain / Engine and ECT / Data List / DPF Differential Pressure" menu using the intelligent tester.
Reference: 
Condition
Differential Pressure Output
Sensor Condition
Engine switch on (IG)
Approximately 0 kPa
Normal
Always
-5 kPa or less or higher than 99 kPa
Open or short circuit
4000 rpm (No engine load)
Negative output
Incorrect hose routing


MONITOR DESCRIPTION

In order to detect abnormality in the differential pressure sensor assembly, the ECM always monitors the output voltage from the sensor. When the sensor output voltage deviates from the normal operating range (between 0.4 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction in the sensor circuit and illuminates the MIL.

WIRING DIAGRAM

A165731E33

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  3. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK WIRE HARNESS (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY - ECM)
  1. Disconnect the differential pressure sensor assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C129-2 (PEX) - C91-7 (PEX)
    Always
    Below 1 Ω
    C129-3 (VC) - C91-13 (VCPX)
    Always
    Below 1 Ω
    C129-1 (E2) - C91-14 (EPEX)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C129-2 (PEX) or C91-7 (PEX) - Body ground
    Always
    10 kΩ or higher
    C129-3 (VC) or C91-13 (VCPX) - Body ground
    Always
    10 kΩ or higher
    C129-1 (E2) or C91-14 (EPEX) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the differential pressure sensor assembly connector.

  1. Reconnect the ECM connector.



NG
Go to step 5
OK


2. CHECK TERMINAL VOLTAGE (VC)

  1. A204467E16
    Disconnect the differential pressure sensor assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C129-3 (VC) - Body ground
    Engine switch on (IG)
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Differential Pressure Sensor Assembly)

  1. Reconnect the differential pressure sensor assembly connector.



NG
Go to step 4
OK


3. REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY
  1. Replace the differential pressure sensor assembly (Click here).



NEXT
Go to step 6
4. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 6
5. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


6. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the engine switch on (IG) and wait for 5 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END


← P2453 Diesel Particulate Filter Pressure Sensor "A" Circuit Range/Performance (from Aug 2014)P2454 Diesel Particulate Filter Pressure Sensor "A" Circuit Low (+ P2455) (from Aug 2014) →