2013-2015 Land Cruiser Prado · Service Manual Steering

REASSEMBLY

Removal / installation · Vehicles built from Aug 2013

NOTICE:
When installing parts, coat the parts indicated by arrows with power steering fluid (Click here).


1. INSTALL VANE PUMP HOUSING OIL SEAL
  1. Coat the lip of a new oil seal with MP grease.

  1. C114702E01
    Using SST and a press, press in the oil seal.
    SST
    09950-60010   (09951-00280)
    09950-70010   (09951-07100)

    NOTICE:
    Make sure that the oil seal is installed facing in the correct direction as shown in the illustration.


2. INSTALL VANE PUMP SHAFT WITH VANE PUMP PULLEY
  1. Coat the inside surface of the bushing in the vane pump front housing with power steering fluid.

  1. C114703E02
    Gradually insert the vane pump shaft with vane pump pulley.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    1. Do not damage the lip of the oil seal in the vane pump front housing.
    2. Wrap protective tape around the spline of the vane pump shaft with vane pump pulley in order to prevent damage to the oil seal.


3. INSTALL VANE PUMP FRONT SIDE PLATE

  1. C132035
    Coat a new O-ring with power steering fluid and install it to the vane pump front housing.

  1. C107035
    Coat a new O-ring with power steering fluid and install it to the front side plate.

  1. C132040E03
    Align the notch of the front side plate with the notch of the vane pump front housing and install the front side plate.
    Text in Illustration 
    *a
    Align

    NOTICE:
    Make sure that the front side plate is installed facing in the correct direction.


4. INSTALL VANE PUMP CAM RING

  1. C139139E03
    Align the notch of the cam ring with the notch of the front side plate and install the cam ring with the inscribed mark facing upward.
    Text in Illustration 
    *a
    Align
    *b
    Inscribed Mark

    NOTICE:
    Make sure that the cam ring is installed facing in the correct direction.


5. INSTALL VANE PUMP ROTOR

  1. C107038
    Install the vane pump rotor.

    HINT:
    The vane pump rotor can be installed with either side facing up.

  1. Coat the 10 vane pump plates with power steering fluid.

  1. C141370E02
    Install the vane pump plates with the round end facing outward.
    Text in Illustration 
    *a
    Round End
    *b
    Outward

    NOTICE:
    Make sure that the vane pump plates are installed facing in the correct direction.


6. INSTALL VANE PUMP SHAFT SNAP RING
  1. Using a screwdriver and snap ring expander, install a new shaft snap ring to the vane pump shaft.

    NOTICE:
    1. Do not expand the shaft snap ring any further than needed.
    2. Make sure that the shaft snap ring fits completely into the groove.
    3. Do not damage the vane pump rotor and shaft.


7. INSTALL VANE PUMP REAR HOUSING

  1. C107040
    Coat a new O-ring with power steering fluid and install it to the rear housing.

  1. C136780E05
    Align the straight pin of the rear housing with the notches of the cam ring, front side plate and vane pump front housing.
    Text in Illustration 
    *a
    Align

    NOTICE:
    Make sure that the O-ring is not protruding from anywhere when installing the vane pump rear housing.

  1. Install the rear housing with the 4 bolts.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }


8. SECURE VANE PUMP ASSEMBLY

  1. C215464E01
    Using SST, secure the vane pump in a vise.
    SST
    09630-00014   (09631-00132)


9. INSPECT TOTAL PRELOAD
  1. Check that the pump rotates smoothly without abnormal noise.

  1. Temporarily install a service bolt.

    Recommended Service Bolt:
    Item
    Value
    Thread diameter
    10 mm (0.394 in.)
    Thread pitch
    1.25 mm (0.0492 in.)
    Bolt length
    50 mm (1.97 in.)

  1. C053369E12
    Using a torque wrench, measure the pump rotating torque.

    Standard rotating torque:
    0.3 N*m (3 kgf*cm, 2 in.*lbf) or less

    Text in Illustration 
    *a
    Service Bolt
    If the rotating torque is not as specified, check the vane pump housing oil seal.


10. INSTALL SUCTION PORT UNION
  1. Coat a new O-ring with power steering fluid and install it to the suction port union.

  1. Install the suction port union to the vane pump with the bolt.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

← INSPECTION (from Aug 2013)INSTALLATION (from Aug 2013) →