2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P1229 Fuel Pump System

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

P1229 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idling for 60 seconds
The actual fuel pressure exceeds the target fuel pressure by 5000 kPa or higher for 30 seconds.
(1 trip detection logic)
  1. Short in suction control valve circuit
  2. Suction control valve
  3. Fuel pressure sensor (common rail assembly)
  4. ECM
Related Data List 
DTC No.
Data List
P1229
  1. Fuel Press
  2. Target Common Rail Pressure
  3. Injection Pressure Correction
  4. Target Pump SCV Current
  5. Pump SCV Learning Value

HINT:
  1. For more information on the fuel supply pump assembly (suction control valve) and common rail system, refer to System Description (Click here).
  2. When DTC P1229 is stored, check the internal fuel pressure of the common rail by entering the following menus: Powertrain / Engine and ECT / Data List / Fuel Press, Target Common Rail Pressure.
    Under a stable condition such as idling after warm up the engine, Fuel Press is within +/-5000 kPa of Target Common Rail Pressure when normal.
  3. When there is a problem with the movement of the fuel supply pump assembly (when Fuel Press is higher than Target Common Rail Pressure due to a problem in which the suction valve has difficulty closing), the values of Injection Pressure Correction and Target Pump SCV Current decrease.


MONITOR DESCRIPTION

  1. P1229 (Fuel overfeed):
    The ECM stores this DTC if the actual fuel pressure inside the common rail remains higher than the target fuel pressure, despite the ECM closing the suction control valve. This DTC indicates that the suction control valve may be stuck open, or there may be a short in its circuit.
    If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the engine switch is turned off.

WIRING DIAGRAM

Refer to DTC P0088 (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  3. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
  2. When this DTC is stored, be sure to carefully examine "Fuel Press", "Target Common Rail Pressure", "Target Pump SCV Current", and "Pump SCV Learning Value" in the freeze frame data.


1. CHECK OTHER DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P1229 and "P0190, P0192 and/or P0193" are output
    B
    Except above
    A



B
GO TO FUEL RAIL PRESSURE SENSOR CIRCUIT (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (FUEL PRESS AND TARGET COMMON RAIL PRESSURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Start the engine and warm it up.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.

  1. Check that the internal fuel pressure of the common rail is within the specification below.

    OK:
    Fuel Press is within 5000 kPa of Target Common Rail Pressure when engine is idling after warm up the engine.



NG
Go to step 3
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

3. CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
  1. Disconnect the suction control valve connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C71-1 - C92-23 (PCV+)
    Always
    Below 1 Ω
    C71-2 - C92-12 (PCV-)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C71-1 or C92-23 (PCV+) - Body ground
    Always
    10 kΩ or higher
    C71-2 or C92-12 (PCV-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the suction control valve connector.

  1. Reconnect the ECM connector.



OK
Go to step 6

NG
Go to step 4
4. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


5. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure.

  1. A176220E18
    Take a snapshot with the intelligent tester during the Active Test.
    Text in Illustration 
    *1
    Snapshot Button

    HINT:
    Detailed graphs can be displayed by transferring the stored snapshot from the tester to a PC (personal computer) with Intelligent Viewer installed.

  1. Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed (Click here).

    HINT:
    In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.

    A227749E01

    OK:
    The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.

    HINT:
    1. "Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.
    2. "Fuel Press" is the actual fuel pressure.

    Result 
    Result
    Proceed to
    The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.
    B
    Except above
    A



B
Go to step 10
A


6. REPLACE FUEL FILTER ELEMENT SUB-ASSEMBLY
  1. Replace the fuel filter element sub-assembly (Click here).


NEXT


7. REPLACE SUCTION CONTROL VALVE
  1. Replace the suction control valve (Click here).


NEXT


8. BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system (Click here).


NEXT


9. PERFORM FUEL SUPPLY PUMP INITIALIZATION
  1. Perform fuel supply pump initialization (Click here).


NEXT


10. CHECK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the engine switch off for 30 seconds or more.

  1. Start the engine.

  1. Idle the engine for 60 seconds, and then run it at 2500 rpm without load for 60 seconds.

  1. Confirm that the DTC is not output again.

    HINT:
    Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.

    1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

    2. Input DTC P1229.

    3. Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, increase the idling time.


NEXT

END


← P1229 Fuel Pump System (Aug 2013 – Jul 2014)P1251 Turbocharger / Supercharger Overboost Condition (Too High) (Aug 2013 – Jul 2014) →