2013-2015 Land Cruiser Prado · Service Manual Drivetrain

REMOVAL

Removal / installation · Vehicles built from Aug 2013


1. REMOVE REAR ENGINE UNDER COVER ASSEMBLY
  1. Remove the 4 bolts and rear engine under cover.


2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts.

  1. A224743
    Unhook the engine under cover from the vehicle body as shown in the illustration.


3. REMOVE FRONT FENDER APRON SEAL RH

  1. A223336
    Remove the 4 clips and fender apron seal.


4. REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL RH

  1. A223337
    Remove the 5 clips and fender apron seal.


5. REMOVE FRONT BUMPER COVER (w/ Air Cooled Transmission Oil Cooler)
  1. Remove the front bumper cover (Click here).


6. DRAIN ENGINE COOLANT (w/o Air Cooled Transmission Oil Cooler)

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


A273797E01
Text in Illustration 
*1
Reservoir Cap
*2
Radiator Cap
*3
Radiator Drain Cock Plug
*4
Cylinder Block Drain Cock Plug
  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap and drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the cylinder block drain cock plug and drain the coolant from the engine.


7. REMOVE NO. 2 OIL COOLER INLET HOSE AND NO. 2 OIL COOLER OUTLET HOSE (w/o Air Cooled Transmission Oil Cooler)

  1. C214592
    Disconnect the No. 2 oil cooler inlet hose and No. 2 oil cooler outlet hose from the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube.

  1. Disconnect the 2 hoses from the transmission oil thermostat and remove them.

    NOTICE:
    When disconnecting the hoses from the tube, support the tube by hand and be careful to prevent the tube from being deformed.


8. REMOVE TRANSMISSION OIL COOLER ASSEMBLY (w/o Air Cooled Transmission Oil Cooler)

  1. C218105
    Disconnect the 2 water by-pass hoses from the transmission oil cooler.

    NOTICE:
    Use a container to catch any coolant which flows out of the water by-pass hoses.

  1. C214428
    Disconnect the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose from each oil cooler tube union.

  1. Remove the 3 bolts and transmission oil cooler with transmission oil thermostat.

  1. Remove the 2 hoses from the transmission oil thermostat.

  1. Remove the 3 bolts and transmission oil cooler from the transmission oil thermostat.

  1. C214429
    Remove the 2 O-rings from the grooves of transmission oil cooler.


9. REMOVE NO. 3 OIL COOLER INLET HOSE AND NO. 3 OIL COOLER OUTLET HOSE

C213424
  1. Detach the claw to open the No. 1 flexible hose clamp.

  1. Disconnect the No. 3 oil cooler inlet hose and No. 3 oil cooler outlet hose from the No. 2 oil cooler tube.

  1. Disconnect the 2 hoses from the oil cooler inlet tube and No. 1 oil cooler outlet tube and remove them.

    NOTICE:
    When disconnecting the hoses from the tube, support the tube by hand and be careful to prevent the tube from being deformed.


10. REMOVE NO. 1 OIL COOLER INLET TUBE AND NO. 1 OIL COOLER OUTLET TUBE (w/o Air Cooled Transmission Oil Cooler)

  1. C219132
    Remove the 2 bolts to open the 2 No. 2 flexible hose clamps and remove 2 oil cooler tubes.

  1. Remove the 2 bolts and 2 No. 2 flexible hose clamps.


11. REMOVE NO. 1 OIL COOLER INLET TUBE AND NO. 1 OIL COOLER OUTLET TUBE (w/ Air Cooled Transmission Oil Cooler)

  1. C218111E01
    Using a union nut wrench, disconnect the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube from each oil cooler tube union.

  1. Remove the 2 bolts to open the 2 No. 2 flexible hose clamps and remove the 2 oil cooler tubes.

  1. Remove the 2 bolts and 2 No. 2 flexible hose clamps.


12. REMOVE NO. 4 OIL COOLER INLET HOSE AND NO. 4 OIL COOLER OUTLET HOSE

C213428E03
  1. Disconnect the No. 4 oil cooler inlet hose and No. 4 oil cooler outlet hose from the radiator.

  1. Disconnect the 2 hoses from the No. 2 oil cooler tube and remove them.

    Text in Illustration 
    *A
    w/o Air Cooled Transmission Oil Cooler
    *B
    w/ Air Cooled Transmission Oil Cooler

    NOTICE:
    When disconnecting the hoses from the tube, support the tube by hand and be careful to prevent the tube from being deformed.


13. REMOVE NO. 5 OIL COOLER INLET HOSE AND NO. 5 OIL COOLER OUTLET HOSE (w/ Air Cooled Transmission Oil Cooler)

C218107
  1. Disconnect the No. 5 oil cooler inlet hose and No. 5 oil cooler outlet hose from the No. 2 oil cooler tube.

  1. Disconnect the 2 hoses from the No. 3 oil cooler tube and remove them.

    NOTICE:
    When disconnecting the hoses from the tube, support the tube by hand and be careful to prevent the tube from being deformed.


14. REMOVE NO. 2 OIL COOLER TUBE SUB-ASSEMBLY

  1. C213425E04
    Remove the 2 bolts and No. 2 oil cooler tube.
    Text in Illustration 
    *A
    w/o Air Cooled Transmission Oil Cooler
    *B
    w/ Air Cooled Transmission Oil Cooler


15. REMOVE NO. 6 OIL COOLER INLET HOSE AND NO. 6 OIL COOLER OUTLET HOSE (w/ Air Cooled Transmission Oil Cooler)

  1. C213758
    Disconnect the No. 6 oil cooler inlet hose and No. 6 oil cooler outlet hose from the No. 3 oil cooler tube.

    NOTICE:
    When disconnecting the hoses from the tube, support the tube by hand and be careful to prevent the tube from being deformed.

  1. Disconnect the 2 hoses from the oil cooler and remove them.


16. REMOVE NO. 3 OIL COOLER TUBE SUB-ASSEMBLY (w/ Air Cooled Transmission Oil Cooler)

  1. C213760
    Remove the bolt and No. 3 oil cooler tube.


17. REMOVE OIL COOLER ASSEMBLY (w/ Air Cooled Transmission Oil Cooler)

  1. C213430
    Remove the 3 bolts and oil cooler.

  1. C213759
    Remove the 2 bolts and oil cooler brackets.

← COMPONENTS (from Aug 2013)INSTALLATION (from Aug 2013) →