2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.


2. REMOVE RADIATOR GRILLE

B357908E01
  1. Put protective tape around the radiator grille.

  1. Remove the 4 screws.

  1. Detach the 8 claws and remove the radiator grille.

    Text in Illustration 
    *1
    Protective Tape


3. REMOVE FRONT BUMPER COVER

  1. B353268
    Remove the 2 screws.

    HINT:
    Use the same procedure for the screws on the other side.

  1. B353353E01
    Remove the 2 screws.
    Text in Illustration 
    *1
    Screw
    *2
    Bolt A
    *3
    Bolt B

  1. Remove the 2 bolts labeled A and 2 bolts labeled B.

  1. B353270E01
    Put protective tape around the front bumper cover.
    Text in Illustration 
    *1
    Protective Tape

  1. Remove the 4 clips.

  1. Detach the 16 claws and remove the front bumper cover.

    NOTICE:
    Do not hold the middle of the front bumper cover, as it may become reformed.

  1. w/ TOYOTA Parking Assist-sensor System, w/ Fog Light:
    Disconnect the 3 connectors.

  1. w/ TOYOTA Parking Assist-sensor System, w/o Fog Light:
    Disconnect the connector.

  1. w/o TOYOTA Parking Assist-sensor System, w/ Fog Light:
    Disconnect the 2 connectors.

  1. w/ Headlight Cleaner System:
    Disconnect the No. 1 headlight cleaner hose.


4. REMOVE FRONT BUMPER ENERGY ABSORBER

  1. B353275
    Remove the front bumper energy absorber.


5. REMOVE FRONT BUMPER LOWER COVER

  1. B353272
    Remove the clip.

  1. Remove the 5 bolts and front bumper lower cover.


6. REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY

  1. B353276
    Remove the 6 nuts and front bumper reinforcement sub-assembly.


7. REMOVE FRONT BUMPER NO. 2 EXTENSION SUB-ASSEMBLY LH

  1. B353271
    Remove the 4 bolts and front bumper No. 2 extension sub-assembly LH.


8. REMOVE FRONT BUMPER NO. 2 EXTENSION SUB-ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


9. REMOVE FRONT BUMPER SIDE SUPPORT LH

  1. B353273
    Remove the screw and bolt.

  1. Detach the 2 claws and remove the front bumper side support LH.


10. REMOVE FRONT BUMPER SIDE SUPPORT RH

HINT:
Use the same procedure described for the LH side.


11. REMOVE FRONT BUMPER CENTER UPPER RETAINER

  1. B353277
    Remove the 3 bolts and front bumper center upper retainer.


12. REMOVE HEADLIGHT ASSEMBLY LH
  1. for Halogen Headlight:
    (Click here)

  1. for LED Headlight:
    (Click here)


13. REMOVE HEADLIGHT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


14. REMOVE FRONT BUMPER BRACKET SUB-ASSEMBLY LH

  1. B353278
    Remove the 2 bolts and front bumper bracket sub-assembly LH.


15. REMOVE FRONT BUMPER BRACKET SUB-ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.

← COMPONENTS (from Aug 2013)REMOVAL (from Aug 2014) →