2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P1626 Idle Signal Output Value Too Low

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The ECM reduces injector operation speed and applied voltage to the injector to reduce the sound it produces during idling. To do this, the ECM outputs applied voltage switching signals to terminal IJEN of the injector driver from terminal IDLO of the ECM.
P1626 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Warm up the engine and idle it for 5 seconds
With the engine running at idle, voltage of the ECM IDLO terminal is 0.05 V or less for 5 seconds or more (1 trip detection logic).
  1. Open or short in idle control circuit
  2. injector driver
  3. ECM
P1627 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Warm up the engine and idle it for 5 seconds
With the engine running at speeds higher than idle, voltage of the ECM IDLO terminal is 3.4 V or higher for 5 seconds or more (1 trip detection logic).
  1. Open or short in idle control circuit
  2. injector driver
  3. ECM

WIRING DIAGRAM

A205143E12

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  3. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - ECM)
  1. Disconnect the injector driver connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C124-2 (IJEN) - C92-19 (IDLO)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C124-2 (IJEN) or C92-19 (IDLO) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the injector driver connector.

  1. Reconnect the ECM connector.



NG
Go to step 5
OK


2. REPLACE INJECTOR DRIVER
  1. Replace the injector driver (Click here).


NEXT


3. CHECK ANY OTHER DTCS OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    P1626 or P1627 is output
    B



B
Go to step 4
A

END

4. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 6
5. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


6. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. After warming up the engine, idle the engine for 5 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END


← P1626 Idle Signal Output Value Too Low (+ P1627) (Aug 2013 – Jul 2014)P2002 Particulate Trap Efficiency Below Threshold (Bank1) (Aug 2013 – Jul 2014) →