2013-2015 Land Cruiser Prado · Service Manual Brake

C1253 Pump Motor Relay

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The motor relay (semiconductor relay) is built into the master cylinder solenoid and drives the pump motor based on a signal from the skid control ECU.
DTC Code
DTC Detection Condition
Trouble Area
C1253
There is a motor system circuit (motor input circuit) malfunction.
  1. ABS NO. 1 fuse
  2. Motor relay circuit
  3. Master cylinder solenoid (Skid control ECU)

WIRING DIAGRAM

C173280E03

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the master cylinder solenoid, perform calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MOTOR RELAY)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Start the engine.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Motor Relay
    Motor relay
    Relay ON/OFF
    An operating sound of the motor can be heard.

  1. Check the operating sound of the motor individually when operating it with the intelligent tester.

    OK:
    An operating sound of the motor can be heard.



NG
Go to step 3
OK


2. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Depress the brake pedal more than 40 times.

  1. Turn the ignition switch to ON.

  1. Wait until the pump motor stops.

  1. Depress the brake pedal several times until the pump motor turns on. (Procedure A)

  1. Wait until the pump stops. (Procedure B)

  1. Repeat the above steps (procedure A and B) 3 more times.

  1. Check if the same DTC is output (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output (for LHD)
    B
    DTC is output (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK TERMINAL VOLTAGE (+BM1, +BM2)
  1. Disconnect the A7 and A8 skid control ECU connectors.

  1. C124799E49
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A7-2 (+BM1) - Body ground
    Always
    11 to 14 V
    A8-2 (+BM2) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)
  1. Disconnect the A7 and A8 skid control ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A7-1 (GND1) - Body ground
    Always
    Below 1 Ω
    A7-32 (GND2) - Body ground
    Always
    Below 1 Ω
    A8-4 (GND3) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Depress the brake pedal more than 40 times.

  1. Turn the ignition switch to ON.

  1. Wait until the pump motor stops.

  1. Depress the brake pedal several times until the pump motor turns on. (Procedure A)

  1. Wait until the pump stops. (Procedure B)

  1. Repeat the above steps (procedure A and B) 3 more times.

  1. Check if the same DTC is output (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output (for LHD)
    B
    DTC is output (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← C1252 Brake Booster Pump Motor on Time Abnormally Long (from Aug 2014)C1253 Pump Motor Relay (from Aug 2014) →