2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

INSTALLATION

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. INSTALL SEAT BELT ANCHOR PLATE ASSEMBLY (for RH Side)
  1. Install the anchor plate with the 2 bolts.


2. INSTALL REAR SEAT OUTER BELT ANCHOR PLATE SUB-ASSEMBLY LH
  1. Install the anchor plate with the bolt.


3. INSTALL REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH

B241721E01

NOTICE:
When installing the retractor, make sure the claws of the vehicle (labeled "a" in the illustration) only contact the installation areas of the retractor.

  1. Align the seat belt positioning holes with the claws and install the retractor of the seat belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the rear No. 2 seat outer belt shoulder anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


4. INSTALL REAR QUARTER TRIM PANEL ASSEMBLY LH
  1. w/ Rear No. 2 Seat:

    1. Attach the 4 clips and 2 guides and pass the rear No. 2 seat outer belt floor anchor through the rear quarter trim panel.

  1. Attach the 7 clips and 2 guides to install the rear quarter trim panel.


5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
  1. Attach the 4 clips and 8 claws to install the deck trim side panel.

  1. Install the 2 bolts and 2 screws.

  1. Install the rear No. 2 seat outer belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the rear No. 1 seat outer belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


6. INSTALL ASSIST GRIP SUB-ASSEMBLY

HINT:
Use the same procedure for the other assist grip.

  1. Install the assist grip with the 2 bolts.


7. INSTALL ASSIST GRIP PLUG

HINT:
Use the same procedure for all assist grip plugs.

  1. Attach the 2 claws to install the assist grip plug.


8. INSTALL FRONT DECK SIDE TRIM COVER LH (w/ Tonneau Cover)

HINT:
Use the same procedure for the other front deck side trim cover.

  1. Attach the 2 claws to install the front deck side trim cover


9. INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

HINT:
Use the same procedure for the other No. 1 tonneau cover holder cap.

  1. Attach the 2 claws to install the No. 1 tonneau cover holder cap.


10. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

HINT:
Use the same procedure for the other No. 1 luggage compartment trim hook.

  1. Install the No. 1 luggage compartment trim hook by turning it clockwise.


11. INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

HINT:
Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.

  1. Attach the 3 claws to install the rear No. 1 seat outer lap belt anchor cover.


12. INSTALL FLOOR SIDE RAIL LH (w/ Deck Rail)
  1. Install the floor side rail with the 3 bolts.


13. INSTALL FLOOR SIDE RAIL RH (w/ Deck Rail)

HINT:
Use the same procedure described for the LH side.


14. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

B238781E01
  1. Align the paint mark on the rear door opening trim weatherstrip with the mark position on the vehicle and install the rear door opening trim weatherstrip as shown in the illustration.

    Text in Illustration 
    *1
    Paint Mark
    *2
    Mark Position


15. INSTALL REAR DOOR SCUFF PLATE LH
  1. Attach the 3 clips, 6 claws and 2 guides to install the rear door scuff plate.


16. INSTALL QUARTER SCUFF PLATE LH
  1. Install the quarter scuff plate with the 2 bolts.


17. INSTALL REAR NO. 1 FLOOR STEP COVER

HINT:
Use the same procedure for all rear No. 1 floor step covers.

  1. Attach the 2 claws to install the rear No. 1 floor step cover.


18. INSTALL REAR NO. 2 SEAT ASSEMBLY LH
  1. for Manual Seat Type:
    Install the rear No. 2 seat assembly LH (Click here).

  1. for Power Seat Type:
    Install the rear No. 2 seat assembly LH (Click here).

← INSPECTION (from Aug 2013)INSTALLATION (from Aug 2014) →