2013-2015 Land Cruiser Prado · Service Manual Suspension

TERMINALS OF ECU

System information · Vehicles built from Aug 2013


CHECK SUSPENSION CONTROL ECU

HINT:
  1. Inspect the connectors from the back side while the connectors are connected.
  2. Check the operation of a particular valve by listening for an operating sound or by using the Data List.

C150345E10
Text in Illustration 
*a
Component with harness connected
(Suspension Control ECU)
-
-
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
R19-9 (SLEX) - Body ground
LG
Exhaust valve
Exhaust valve not operating
Below 1 V
Exhaust valve operating
8 V or higher
R19-10 (GND) - Body ground
W-B
Ground
Always
Below 1 Ω
R19-13 (SBR2) - Body ground
R
Rear height control sensor RH power source
Ignition switch ON
4.5 to 5.5 V
R19-14 (SBL2) - Body ground
R
Rear height control sensor LH power source
Ignition switch ON
4.5 to 5.5 V
R19-15 (SGL2) - Body ground
V
Rear height control sensor LH ground
Always
Below 1 Ω
R19-16 (SGR2) - Body ground
W
Rear height control sensor RH ground
Always
Below 1 Ω
R19-22 (RC) - Body ground
G
AIR SUS relay
Compressor motor not operating
Below 1 V
Compressor motor operating
8 V or higher
R19-24 (SHRL) - Body ground
GR
Rear height control sensor LH
Vehicle being raised
Voltage increases within range of 0.5 to 4.5 V in proportion to vehicle height
Vehicle being lowered
Voltage decreases within range of 0.5 to 4.5 V in proportion to vehicle height
R19-26 (SHRR) - Body ground
W
Rear height control sensor RH
Vehicle being raised
Voltage increases within range of 0.5 to 4.5 V in proportion to vehicle height
Vehicle being lowered
Voltage decreases within range of 0.5 to 4.5 V in proportion to vehicle height
R19-27 (SHR2) - Body ground
B
Height control sensor (for AFS ECU)
Vehicle being raised
Voltage increases within range of 0.5 to 4.5 V in proportion to vehicle height
Vehicle being lowered
Voltage decreases within range of 0.5 to 4.5 V in proportion to vehicle height
A14-9 (SBR) - Body ground
G-B
Front acceleration sensor RH power source
Ignition switch ON
4.5 to 5.5 V
A14-10 (SGR) - Body ground
L-Y
Front acceleration sensor RH ground
Always
Below 1 Ω
A14-15 (SLRL) - Body ground
L
Gate solenoid valve (No. 2 height control valve)
Ignition switch ON
Below 1 V
Engine idling, button of height control switch is pushed from "down" to "up"
8 V or higher
A14-16 (SLRR) - Body ground
V
Leveling solenoid valve (No. 2 height control valve)
Ignition switch ON
Below 1 V
Engine idling, button of height control switch is pushed from "down" to "up"
8 V or higher
A14-17 (RM-) - Body ground
G
Motor lock (-)
Always
Below 1 Ω
A14-18 (SGFR) - Body ground
R-L
Front acceleration sensor RH
Ignition switch ON
0.5 to 4.5 V
A14-19 (RM+) - Body ground
P
Motor lock (+)
Engine idling, vehicle height changes from N to HI by pressing height control switch (While height control compressor assembly operating)
Below 1 V
A14-21 (SGL) - Body ground
W
Height control sensor ground (for AFS ECU)
Always
Below 1 Ω
A14-22 (SBL) - Body ground
R-G
Height control sensor power source (for AFS ECU)
Ignition switch ON
4.5 to 5.5 V
A49-1 (IG) - Body ground
B
IG power supply
Ignition switch ON
11 to 14 V
A49-3 (B) - Body ground
GR
Battery power supply
Always
11 to 14 V
A49-5 (GND) - Body ground
W-B
Ground
Always
Below 1 Ω
A49-7 (CANH) - A49-8 (CANL)
R*1 - W
CAN communication line
Ignition switch off
54 to 69 Ω
GR*2 - W
A49-13 (TD) - Body ground
L
Height control OFF switch
  1. Ignition switch ON
  2. Switch pressed and held
11 to 14 V
  1. Ignition switch ON
  2. Switch not pressed
Below 1 V
A49-14 (DNSW) - Body ground
V
Height control switch "down" side
  1. Ignition switch ON
  2. Switch pressed and held
11 to 14 V
  1. Ignition switch ON
  2. Switch not pressed
Below 1 V
A49-15 (UPSW) - Body ground
P
Height control switch "up" side
  1. Ignition switch ON
  2. Switch pressed and held
11 to 14 V
  1. Ignition switch ON
  2. Switch not pressed
Below 1 V
A49-16 (SGR3) - Body ground
R
Rear acceleration sensor ground
Always
Below 1 Ω
A49-17 (SBR3) - Body ground
W
Rear acceleration sensor power source
Ignition switch ON
4.5 to 5.5 V
A49-22 (TSW2) - Body ground
B
Absorber control switch (COMF)
  1. Ignition switch ON
  2. Absorber control switch set to NORMAL
10 to 14 V
  1. Ignition switch ON
  2. Absorber control switch set to COMF
Below 1.5 V
A49-23 (TSW1) - Body ground
G
Absorber control switch (SPORT)
  1. Ignition switch ON
  2. Absorber control switch set to NORMAL
10 to 14 V
  1. Ignition switch ON
  2. Absorber control switch set to SPORT
Below 1.5 V
A49-26 (SGRR) - Body ground
LG
Rear acceleration sensor
Ignition switch ON
0.5 to 4.5 V
  1. *1: for RHD
  2. *2: for LHD
← PROBLEM SYMPTOMS TABLE (from Aug 2014)DIAGNOSIS SYSTEM (Aug 2013 – Jul 2014) →