PTC Heater Circuit
Circuit diagnosis · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
PTC heater relays are closed in accordance with signals from the air conditioning amplifier assembly and power is supplied to the quick heater assembly installed on the radiator heater unit.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. INSPECT PTC HEATER RELAY (PTC NO. 1, PTC NO. 2, PTC NO. 3) |
Remove the PTC NO. 1, PTC NO. 2 and PTC NO. 3 relays from the engine room No. 2 relay block.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
Battery voltage is applied to terminals 1 and 2
Below 1 Ω
|
|
||||
| OK | |
| 2. CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY |
Remove the air conditioning amplifier assembly with its connectors still connected (Click here).

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
G25-3 (PTC1) - Body ground
- Engine running (1250 rpm or more)
- Temperature setting MAX HOT
- Outside temperature 10°C (50°F) or less
- Engine coolant temperature 79°C (174°F) or less
- Headlight dimmer switch off
- Blower switch off
Below 1 V*
G25-22 (PTC2) - Body ground
- Engine running (1250 rpm or more)
- Temperature setting MAX HOT
- Outside temperature 10°C (50°F) or less
- Engine coolant temperature 76°C (169°F) or less
- Headlight dimmer switch off
- Blower switch off
G25-4 (PTC3) - Body ground
- Engine running (1250 rpm or more)
- Temperature setting MAX HOT
- Outside temperature 10°C (50°F) or less
- Engine coolant temperature 73°C (163°F) or less
- Headlight dimmer switch off
- Blower switch off
G25-3 (PTC1) - Body ground
- Engine running (1250 rpm or more)
- Temperature setting MAX HOT
- Outside temperature 10°C (50°F) or less
- Engine coolant temperature 79°C (174°F) or less
- Headlight dimmer switch off
- Blower switch on
11 to 14 V*
G25-22 (PTC2) - Body ground
- Engine running (1250 rpm or more)
- Temperature setting MAX HOT
- Outside temperature 10°C (50°F) or less
- Engine coolant temperature 76°C (169°F) or less
- Headlight dimmer switch off
- Blower switch on
G25-4 (PTC3) - Body ground
- Engine running (1250 rpm or more)
- Temperature setting MAX HOT
- Outside temperature 10°C (50°F) or less
- Engine coolant temperature 73°C (163°F) or less
- Headlight dimmer switch off
- Blower switch on
- Engine running (1250 rpm or more)
Text in Illustration *a
Component with harness connected
(Air Conditioning Amplifier Assembly)
- HINT:
- *: After the measurement conditions are met, wait 30 seconds before performing measurements.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 2 RELAY BLOCK - AIR CONDITIONING AMPLIFIER) |
Remove the PTC heater relays from the engine room No. 2 relay block.
Disconnect the G25 amplifier connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
PTC NO. 1 relay terminal 1 - G25-3 (PTC1)
Always
Below 1 Ω
PTC NO. 2 relay terminal 1 - G25-22 (PTC2)
PTC NO. 3 relay terminal 1 - G25-4 (PTC3)
PTC NO. 1 relay terminal 1 - Body ground
Always
10 kΩ or higher
PTC NO. 2 relay terminal 1 - Body ground
PTC NO. 3 relay terminal 1 - Body ground
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 2 RELAY BLOCK - QUICK HEATER) |
Remove the PTC heater relays from the engine room No. 2 relay block.
Disconnect the G28 heater connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
PTC NO. 1 relay terminal 3 - G28-2 (B)
Always
Below 1 Ω
PTC NO. 2 relay terminal 3 - G28-3 (B)
PTC NO. 3 relay terminal 3 - G28-1 (B)
PTC NO. 1 relay terminal 3 - Body ground
Always
10 kΩ or higher
PTC NO. 2 relay terminal 3 - Body ground
PTC NO. 3 relay terminal 3 - Body ground
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 2 RELAY BLOCK - BATTERY AND BODY GROUND) |
Remove the PTC heater relays from the engine room No. 2 relay block.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
PTC NO. 1 relay terminal 5 - Body ground
Always
11 to 14 V
PTC NO. 2 relay terminal 5 - Body ground
PTC NO. 3 relay terminal 5 - Body ground
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
PTC NO. 1 relay terminal 2 - Body ground
Always
Below 1 Ω
PTC NO. 2 relay terminal 2 - Body ground
PTC NO. 3 relay terminal 2 - Body ground
| *1 |
PTC NO. 1 Relay |
| *2 |
PTC NO. 2 Relay |
| *3 |
PTC NO. 3 Relay |
| *a |
Component without relay installed (Engine Room No. 2 Relay Block) |
|
|
||||
| OK | |
| 6. INSPECT QUICK HEATER ASSEMBLY |
Remove the quick heater assembly (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 (B) - 1 (E)
Always
Below 1 kΩ
2 (B) - 1 (E)
2 (B) - 2 (E)
3 (B) - 2 (E)
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (QUICK HEATER - BODY GROUND) |
Disconnect the G29 heater connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G29-1 (E) - Body ground
Always
Below 1 Ω
G29-2 (E) - Body ground
Text in Illustration *a
Front view of wire harness connector
(to Quick Heater Assembly)
|
|
||||
| OK | ||
| ||
