TERMINALS OF ECU
System information · Vehicles built from Aug 2013
| TERMINALS OF ECU |
![]() ![]() |
| *a |
Component without harness connected (Skid Control ECU [Brake Actuator Assembly]) |
| Terminal No. (Symbol) |
Terminal Description |
| 1 (GND1) |
Skid control ECU ground |
| 2 (STP) |
Stop light switch input |
| 4 (RL-) |
Rear wheel speed LH (-) signal input |
| 5 (RL+) |
Rear wheel speed LH (+) power supply output |
| 6 (FR-) |
Front wheel speed RH (-) signal input |
| 7 (FR+) |
Front wheel speed RH (+) power supply output |
| 8 (EX0) |
Stop light control ECU output |
| 9 (EXI4) |
Center differential lock detection switch input |
| 11 (SP1) |
Speed signal output for speedometer |
| 12 (+BS) |
Solenoid relay power supply |
| 13 (GND2) |
Pump motor ground |
| 14 (CANL) |
CAN communication line low |
| 16 (RR-) |
Rear wheel speed RH (-) signal input |
| 17 (RR+) |
Rear wheel speed RH (+) power supply output |
| 18 (FL-) |
Front wheel speed LH (-) signal input |
| 19 (FL+) |
Front wheel speed LH (+) power supply output |
| 22 (STP2) |
Stop light control ECU input |
| 24 (BM) |
Motor relay power supply |
| 25 (CANH) |
CAN communication line high |
| 27 (FSW+) |
Brake pedal load sensing switch input |
| 29 (HZRI) |
Hazard warning switch input |
| 30 (CSW) |
VSC OFF switch input |
| 33 (TS) |
Sensor check input |
| 34 (IG1) |
ECU power supply |
| TERMINAL INSPECTION |
![]() ![]() |
| *a |
Front view of wire harness connector (to Skid Control ECU [Brake Actuator Assembly]) |
Disconnect the connector and measure the voltage or resistance on the wire harness side.
- HINT:
- Voltage cannot be measured with the connector connected to the skid control ECU (brake actuator assembly) as the connector is watertight.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A6-1 (GND1) - Body ground
W-B - Body ground
Skid control ECU ground
Always
Below 1 Ω
A6-2 (STP) - Body ground
V - Body ground
Stop light switch input
Brake pedal depressed → released
8 to 14 V → Below 1.5 V
A6-12 (+BS) - Body ground
L-R - Body ground
Solenoid relay power supply
Always
11 to 14 V
A6-13 (GND2) - Body ground
W-B - Body ground
Pump motor ground
Always
Below 1 Ω
A6-22 (STP2) - Body ground
L - Body ground
Stop light control ECU input
Brake pedal depressed → released
8 to 14 V → Below 1.5 V
A6-24 (BM) - Body ground
B - Body ground
Motor relay power supply
Always
11 to 14 V
A6-25 (CANH) - A6-14 (CANL)
B*1, R*2 - W
CAN bus
Ignition switch off
54 to 69 Ω
A6-27 (FSW+) - Body ground
V-G - Body ground
Brake pedal load sensing switch input
Brake pedal depressed → released
950 to 1050 Ω → 203 to 223 Ω
A6-30 (CSW) - Body ground
B - Body ground
VSC OFF switch input
VSC OFF switch held on → off (Not pressed)
Below 1 Ω → 10 kΩ or higher
A6-34 (IG1) - Body ground
G - Body ground
ECU power supply
Ignition switch ON
11 to 14 V
- *1: for LHD
- *2: for RHD
- *1: for LHD


