C0273 Open in ABS Motor Relay Circuit
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Also covers:
- C0274 Short in ABS Motor Relay Circuit
- C1361 Short in ABS Motor Fail Safe Relay Circuit
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The motor relay supplies power to the pump motor. While the ABS is activated, the ECU turns the motor relay on and operates the pump motor.If the voltage supplied to the motor relay (BM) is below the DTC detection threshold due to low voltage from the battery or generator, these DTCs may be stored.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| C0273 |
Either condition is met:
|
|
| C0274 |
When the motor relay is off, the motor relay remains closed for 4 seconds or more. |
|
| C1361 |
Immediately after the ignition switch is turned to ON, the relay contact is closed for 4 seconds when the motor fail-safe relay is off. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the skid control ECU (brake actuator assembly), perform calibration (Click here).
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- When replacing the skid control ECU (brake actuator assembly), perform calibration (Click here).
- HINT:
- When DTC C1241 is output together with DTC C0273, C0274 and/or C1361, inspect and repair the trouble areas indicated by DTC C1241 first (Click here).
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MOTOR RELAY) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
ABS/VSC/TRC Tester Display
Test Part
Control Range
Diagnostic Note
Motor Relay
Motor relay
Relay ON / OFF
The operating sound of the motor can be heard.
Check the operating sound of the motor relay when operating it with the intelligent tester.
Result Result
Proceed to
Operating sound is not heard
A
Operating sound is heard
B
|
|
||||
| A | |
| 2. CHECK TERMINAL VOLTAGE (BM) |
Turn the ignition switch off.
Disconnect the A6 skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Condition
Specified Condition
A6-24 (BM) - Body ground
Always
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (GND2 TERMINAL) |
Disconnect the A6 skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A6-13 (GND2) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 4. RECONFIRM DTC |
- HINT:
- This code is stored when a problem is identified in the skid control ECU (brake actuator assembly).
- The motor relay is in the skid control ECU (brake actuator assembly).
- Therefore, motor relay inspections and motor relay unit inspections cannot be performed. Be sure to check if the DTC is output before replacing the skid control ECU (brake actuator assembly).
Turn the ignition switch off.
Reconnect the skid control ECU (brake actuator assembly) connector.
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTC not output
A
DTC output
B
- HINT:
- If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch ON and the stop light switch off, the ECU performs self-diagnosis of the motor and solenoid circuits.
- If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harnesses, and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.
- If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness. The DTCs were probably output due to a bad connection of the connector terminal.
- If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch ON and the stop light switch off, the ECU performs self-diagnosis of the motor and solenoid circuits.
|
|
||||
| A | ||
| ||
