2013-2015 Land Cruiser Prado · Service Manual Brake

DTC CHECK / CLEAR

Troubleshooting · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


DTC CHECK/CLEAR (When Using Intelligent Tester)
  1. Check for DTCs.

    1. Turn the ignition switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the intelligent tester on.

    5. Enter the following menus: Chassis / ABS/VSC/TRC / DTC.

    6. Check the details of the DTCs (Click here).

      HINT:
      Refer to the intelligent tester operator's manual for further details.

  2. Clear the DTCs.

    1. Turn the ignition switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the intelligent tester on.

    5. Enter the following menus: Chassis / ABS/VSC/TRC / DTC.

    6. Clear the DTCs by following the prompts on the intelligent tester.

      HINT:
      Refer to the intelligent tester operator's manual for further details.


DTC CHECK/CLEAR (When Using SST Check Wire)

  1. C146309E17
    Check for DTCs.
    Text in Illustration 
    *a
    Front view of DLC3

    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

    2. Turn the ignition switch to ON.

    3. Read the DTCs output from the ABS warning light in the combination meter.

      HINT:
      1. When the system is normal, the ABS warning light blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).
      2. When only 1 DTC is output, the light outputs the same code after an interval of 4 seconds. Example: when DTC 21 is output, the light blinks twice, turns off for 1.5 seconds, blinks once, turns off for 4 seconds, and then repeats this output pattern.
      3. When 2 or more DTCs are output, the light outputs the codes with an interval of 2.5 seconds between each different code, and the output of all codes repeats after an interval of 4 seconds.
      4. If no code is output, inspect the TC and CG terminal circuit and ABS warning light circuit.
      Trouble Area
      See Procedure
      TC and CG terminal circuit
      Click here
      ABS warning light circuit (Remains on)
      Click here
      ABS warning light circuit (Does not come on)
      Click here

    4. Codes are explained in the DTC chart.

      ABS DTC 
      ABS Warning Light Display
      Intelligent Tester Display
      11
      C0278
      12
      C0279
      13
      C0273
      14
      C0274
      21
      C0226
      22
      C0236
      23
      C0246
      24
      C0256
      25
      C1225
      31
      C1401
      C1405
      C1409
      32
      C1402
      C1406
      C1410
      33
      C1403
      C1407
      C1411
      34
      C1404
      C1408
      C1412
      35
      C1413
      36
      C1414
      37
      C1337
      38
      C1415
      39
      C1416
      41
      C1241
      C1417
      43
      C1243
      44
      C1419
      C1420
      C1442
      45
      C1245
      46
      C1421
      C1422
      C1423
      C1424
      49
      C1425
      C1426
      51
      C1427
      C1428
      59
      C1203
      67
      C1429
      C1430
      C1431
      68
      C1268
      91
      C1361
      94
      U0073
      95
      U0124
      97
      C1381
      A1*
      U0114
      1. *: The light blinks 10 times, turns off for 1.5 seconds, and then blinks once.

    5. Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.

      HINT:
      If 2 or more DTCs are output at the same time, the DTCs are output in ascending order.

  2. Clear the DTCs.

    1. C146309E17
      Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
      Text in Illustration 
      *a
      Front view of DLC3
      SST
      09843-18040  

    2. Turn the ignition switch to ON.

    3. Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.

    4. Check that the ABS warning light blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).

    5. Remove SST from the terminals of the DLC3.


END OF DTC CHECK/CLEAR
  1. Turn the ignition switch to ON.

  2. Check that the ABS warning light goes off within approximately 3 seconds after turning the ignition switch to ON.

← DIAGNOSIS SYSTEM (from Aug 2014)DTC CHECK / CLEAR (from Aug 2014) →