ON-VEHICLE INSPECTION
Inspection · Vehicles built from Aug 2013
| INSPECT V BELT |
![]() ![]() |
Visually check the belt for cracks, oiliness or wear. Check that the belt does not touch the bottom of the pulley groove.
If necessary, replace the belt.Text in Illustration *a
CORRECT
*b
INCORRECT
*c
Clearance
Check the vane pump V belt deflection by pressing on the belt at the point indicated in the illustration with 98 N (10 kgf, 22 lbf) of force.

- Standard Deflection:
Item
Specified Condition
New belt
8 to 10 mm
(0.314 to 0.393 in.)
Used belt
10 to 15 mm
(0.393 to 0.590 in.)
Text in Illustration *1
Vane Pump Pulley
*2
Crankshaft Pulley


Measuring Point for Belt Tension
- If necessary, adjust the vane pump V belt deflection.
Reference:
Using a belt tension gauge, check the cooler compressor V belt tension.- Standard Tension:
Item
Specified Condition
New belt
441 to 539 N
(45 to 55 kgf, 99.1 to 121.2 lbf)
Used belt
196 to 343 N
(20 to 35 kgf, 44.1 to 77.1 lbf)
- If the belt tension is not as specified, adjust it.
- NOTICE:
- Check the vane pump V belt tension at the specified point.
- When installing a new belt, set its deflection value as specified.
- Perform the V belt tension and deflection value check after idling the engine for a few minutes.
- When using a belt tension gauge, confirm the accuracy first by using a master gauge.
- When reinstalling a belt used for over 5 minutes, perform the check based on the used deflection value.
- When checking a belt used for over 5 minutes, confirm the deflection value is within the specified range.
- Check the vane pump V belt tension at the specified point.
Check the cooler compressor V belt deflection by pressing on the belt at the point indicated in the illustration with 98 N (10 kgf, 22 lbf) of force.

- Standard Drive Deflection:
Item
Specified Condition
New belt
11 to 15 mm
(0.433 to 0.590 in.)
Used belt
15 to 20 mm
(0.590 to 0.787 in.)
Text in Illustration *1
Cooler Compressor
*2
Idle Pulley
*3
Crankshaft Pulley


Measuring Point for Belt Tension
- If necessary, adjust the cooler compressor V belt deflection.
Reference:
Using a belt tension gauge, check the cooler compressor V belt tension.- Standard Tension:
Item
Specified Condition
New belt
372 to 608 N
(38 to 62 kgf, 83.6 to 136.7 lbf)
Used belt
196 to 392 N
(20 to 40 kgf, 44.1 to 88.1 lbf)
- If the belt tension is not as specified, adjust it.
- NOTICE:
- Check the cooler compressor V belt tension at the specified point.
- When installing a new belt, set its deflection value as specified.
- Perform the V belt tension and deflection value check after idling the engine for a few minutes.
- When using a belt tension gauge, confirm the accuracy first by using a master gauge.
- When reinstalling a belt used for over 5 minutes, perform the check based on the used deflection value.
- When checking a belt used for over 5 minutes, confirm the deflection value is within the specified range.
- Check the cooler compressor V belt tension at the specified point.
Check the fan and generator V belt deflection by pressing on the belt at the point indicated in the illustration with 98 N (10 kgf, 22 lbf) of force.

- Standard Deflection:
Item
Specified Condition
New belt
7.0 to 10 mm
(0.276 to 0.393 in.)
Used belt
10 to 14 mm
(0.393 to 0.551 in.)
Text in Illustration *1
Water Pump Pulley
*2
Generator
*3
Crankshaft Pulley


Measuring Point for Belt Tension
- If necessary, adjust the fan and generator V belt deflection.
Reference:
Using a belt tension gauge, check the fan and generator V belt tension.- Standard Tension:
Item
Specified Condition
New belt
441 to 539 N
(45 to 55 kgf, 99.1 to 121.2 lbf)
Used belt
196 to 343 N
(20 to 35 kgf, 44.1 to 77.1 lbf)
- If the belt tension is not as specified, adjust it.
- NOTICE:
- Check the fan and generator V belt tension at the specified point.
- When installing a new belt, set its deflection value as specified.
- Perform the V belt tension and deflection value check after idling the engine for a few minutes.
- When using a belt tension gauge, confirm the accuracy first by using a master gauge.
- When reinstalling a belt used for over 5 minutes, perform the check based on the used deflection value.
- When checking a belt used for over 5 minutes, confirm the deflection value is within the specified range.
- Check the fan and generator V belt tension at the specified point.

