2013-2015 Land Cruiser Prado · Service Manual Suspension

C1752/52 Compressor Motor Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the "up" side of the height control switch is pressed, a signal is sent from terminal RC of the suspension control ECU to switch the AIR SUS relay on. As a result, the relay contacts close and the compressor motor turns on, producing compressed air.
The suspension control ECU detects the amount of current flowing to the compressor motor by means of the differences in potential at terminals RM+ and RM- of the suspension control ECU. In this way, the suspension control ECU monitors the compressor motor circuit for abnormalities.
DTC Code
DTC Detection Condition
Trouble Area
C1752/52
With the AIR SUS relay activated, a lock signal of the height control compressor motor is detected for 4 seconds or more.
  1. AIR SUS fuse
  2. Harness or connector
  3. Height control compressor
  4. Suspension control ECU

WIRING DIAGRAM

C218586E01

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the suspension control ECU, perform registration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
If DTC C1782/82 is output at the same time as C1752/52, perform the inspection necessary for DTC C1782/82 first (Click here).


1. INSPECT SUSPENSION CONTROL RELAY (AIR SUS)
  1. Turn the ignition switch off.

  1. Remove the AIR SUS relay from the engine room relay block.

  1. C149624E14
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    12 V battery voltage is not applied to terminal 1 and 2
    10 kΩ or higher
    12 V battery voltage is applied to terminal 1 and 2
    Below 1 Ω

    Text in Illustration 
    *1
    AIR SUS Relay



NG
REPLACE SUSPENSION CONTROL RELAY (AIR SUS)
OK


2. CHECK TERMINAL VOLTAGE (POWER SUPPLY)

  1. C216861E01
    Remove the AIR SUS relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Engine room relay block AIR SUS relay terminal 5 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Component without AIR SUS Relay
    (Engine Room Relay Block)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (HEIGHT CONTROL COMPRESSOR - AIR SUS RELAY/SUSPENSION CONTROL ECU)
  1. Disconnect the S11 height control compressor connector.

  1. Remove the AIR SUS relay from the engine room relay block.

  1. Disconnect the A14 suspension control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S11-1 (B) - Engine room relay block AIR SUS relay terminal 3
    Always
    Below 1 Ω
    S11-1 (B) - Body ground
    Always
    10 kΩ or higher
    S11-2 (E) - Body ground
    Always
    Below 1 Ω
    A14-19 (RM+) - S11-3 (RM+)
    Always
    Below 1 Ω
    A14-19 (RM+) - Body ground
    Always
    10 kΩ or higher
    A14-17 (RM-) - S11-4 (RM-)
    Always
    Below 1 Ω
    A14-17 (RM-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT HEIGHT CONTROL COMPRESSOR (COMPRESSOR MOTOR)
C214513E03
  1. Remove the height control compressor (Click here).

  1. Apply 12 V battery voltage to the compressor motor and check the operation of the motor.

OK:
Measurement Condition
Specified Condition
12 V battery positive (+) voltage → Terminal 1 (B)
12 V battery negative (-) voltage → Terminal 2 (E)
Motor operates

Text in Illustration 
*a
Component without harness connected
(Height Control Compressor)

NOTICE:
  1. Do not allow the compressor motor to operate for approximately 90 seconds or more.
  2. If the compressor is shorted, locked or has a similar type of malfunction, a large amount of current is flowing. Therefore, if the motor does not operate, immediately stop this inspection.



NG
REPLACE HEIGHT CONTROL COMPRESSOR ASSEMBLY (Click here)
OK

REPLACE SUSPENSION CONTROL ECU (Click here)


← C1752/52 Compressor Motor Malfunction (Aug 2013 – Jul 2014)C1761/61 Continuous Current to Compressor Motor (Aug 2013 – Jul 2014) →