DATA LIST / ACTIVE TEST
System information · Vehicles built from Aug 2013
| DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn ON the intelligent tester.
Enter the following menus: Chassis / KDSS / Data List.
According to the display on the intelligent tester, read the Data List.
KDSS Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Oil Pressure Sensor
Oil pressure sensor/
Min.: -784.79 MPa (-8002.66 kgf/cm2, -113794.55 psi)
Max.: 784.76 MPa (8002.35 kgf/cm2, 113790.20 psi)
2.6 MPa (26.5 kgf/cm2, 377 psi) to 3.0 MPa (30.6 kgf/cm2, 435 psi): When vehicle stopped and fluid temperature 20°C (68°F)
-
Acceleration Sensor
Lateral G/
Min.: -1176.37 m/s2
Max.: -1176.33 m/s2
-
Changes in proportion with acceleration during turning.
Stop Light Switch
Stop light switch/
ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
TC Terminal
TC terminal/
ON or OFF
OFF
-
TS Terminal
TS terminal/
ON or OFF
OFF
-
FR Wheel Speed
Front wheel RH speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
FL Wheel Speed
Front wheel LH speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
RR Wheel Speed
Rear wheel RH speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
RL Wheel Speed
Rear wheel LH speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
IG Power Source Voltage
IG power source voltage/
Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11 to 14 V
-
Steering Angle
Steering angle/
Min.: -49152.0 deg
Max.: 49150.5 deg
-
Changes in proportion with the amount of steering wheel rotation during steering operation.
Compatible Constant Information
Compatible constant information/
Min.: 0
Max.: 255
-
-
Design Constant Information
Design constant information/
Min.: 0
Max.: 255
-
-
Accumulator Valve (Downside)
Stabilizer control solenoid valve (for Lower Chamber)/
ON or OFF
ON: Stabilizer control solenoid valve closed
OFF: Stabilizer control solenoid valve open
-
Accumulator Valve (Upside)
Stabilizer control solenoid valve (for Upper Chamber)/
ON or OFF
ON: Stabilizer control solenoid valve open
OFF: Stabilizer control solenoid valve closed
-
Number of Trouble Codes
Number of trouble codes/
Min.: 0
Max.: 255
0
-
| ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn ON the intelligent tester.
Enter the following menus: Chassis / KDSS / Active Test.
According to the display on the intelligent tester, perform the Active Test.
KDSS Tester Display
Test Part
Control Range
Diagnostic Note
Accumulator Valve (Upside)
Stabilizer control solenoid valve (for Upper Chamber)
Valve ON / OFF
The operating sound of the solenoid (clicking sound) can be heard
ON: Data List ON
OFF: Data List OFF
When the Active Test is performed, the solenoid turns on for 3 seconds.
Accumulator Valve (Downside)
Stabilizer control solenoid valve (for Lower Chamber)
Valve ON / OFF
The Operating sound of the solenoid (clicking sound) can be heard
ON: Data List ON
OFF: Data List OFF
When the Active Test is performed, the solenoid turns on for 3 seconds.