2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

INSTALLATION

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. INSTALL WIPER MOTOR WIRE
  1. Attach the claw to install the wiper motor wire.


2. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY
  1. Using a T30 "TORX" socket, install the wiper motor with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the connector.

  1. w/o Spring:

    1. E197630E01
      Apply MP grease to the crank arm pivot of the front wiper crank.
      Text in Illustration 
      *1
      Crank Arm Pivot
      V100155
      MP grease

    2. E197632
      Connect the rod to the crank arm pivot of the front wiper crank.


3. INSTALL FRONT WIPER CRANK SUB-ASSEMBLY (for RHD, w/ Spring)
  1. Check the automatic stop position.

    1. Check that the motor stops automatically at the automatic stop position (Click here).

  1. E197629E01
    Install the front wiper crank sub-assembly to the front wiper motor assembly with the nut so that center lines of the crank arm spring and wiper link stay are parallel.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

    Text in Illustration 
    *A
    Front Wiper Crank Set Position
    *a
    Center Line of Crank Arm Spring
    *b
    Center Line of Wiper Link Stay

    HINT:
    Hold the front wiper crank sub-assembly by hand when tightening the nut.

  1. E201905E01
    Apply MP grease to the crank arm pivot of the front wiper crank sub-assembly.
    Text in Illustration 
    *1
    Crank Arm Pivot
    V100155
    MP grease

  1. Connect the rod of the windshield wiper link to the front wiper crank.


4. INSTALL WINDSHIELD WIPER MOTOR AND LINK

  1. E197634E01
    Attach the grommet as shown in the illustration.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    Text in Illustration 
    *1
    Grommet

    NOTICE:
    Be careful not to damage the windshield when installing the windshield wiper motor and link assembly.

  1. Install the windshield wiper motor and link with the 2 bolts.

  1. Connect the connector.

  1. Attach the clamp.


5. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E197614E01
    Attach the 10 guides (B).

  1. Attach the 6 claws and guide (A) as shown in the illustration.

    Text in Illustration 
    *1
    Guide A
    *2
    Guide B

  1. Install the 2 clips to the cowl top ventilator louver sub-assembly.


6. INSTALL CENTER NO. 2 COWL TOP VENTILATOR LOUVER
  1. Attach the 2 claws and 3 guides to install the center No. 2 cowl top ventilator louver.


7. INSTALL HOOD TO COWL TOP SEAL

8. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. E112237E08
    When reusing the front wiper arm and blade assembly RH:

    1. Clean the wiper arm serrations.

      Text in Illustration 
      *1
      Wiper Arm Serration
      *2
      Wire Brush
      *3
      Wiper Pivot Serration

  1. When reusing the windshield wiper link assembly:

    1. Clean the wiper pivot serrations with a wire brush.

  1. E197636E01
    Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    Standard 
    Area
    Standard Condition
    a
    7.5 mm (0.295 in.)
    b
    7.5 mm (0.295 in.)
    c
    7.5 mm (0.295 in.)
    d
    7.5 mm (0.295 in.)
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *1
    Ceramic Dot
    *a
    Upper Limit
    *b
    Lower Limit

    HINT:
    1. Hold the wiper arm by hand while tightening the nut.
    2. Raise and lower the wiper arm a few times to confirm that it has settled to the specified position.


9. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E112237E08
    When reusing the front wiper arm and blade assembly LH:

    1. Clean the wiper arm serrations.

      Text in Illustration 
      *1
      Wiper Arm Serration
      *2
      Wire Brush
      *3
      Wiper Pivot Serration

  1. When reusing the windshield wiper link assembly:

    1. Clean the wiper pivot serrations with a wire brush.

  1. E197693E01
    Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    Standard 
    Area
    Standard Condition
    a
    7.5 mm (0.295 in.)
    b
    7.5 mm (0.295 in.)
    c
    7.5 mm (0.295 in.)
    d
    7.5 mm (0.295 in.)
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *1
    Ceramic Dot
    *a
    Upper Limit
    *b
    Lower Limit

    HINT:
    1. Hold the wiper arm by hand while tightening the nut.
    2. Raise and lower the wiper arm a few times to confirm that it has settled to the specified position.

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.


10. INSTALL WINDSHIELD WIPER ARM COVER

  1. E201164
    Attach the 3 claws to install the wiper arm cover.

    HINT:
    Use the same procedure described for the LH side.


11. INSTALL FRONT FENDER TO COWL SIDE SEAL LH
  1. Attach the 5 claws to install the front fender to cowl side seal LH.


12. INSTALL FRONT FENDER TO COWL SIDE SEAL RH

HINT:
Use the same procedure described for the LH side.


13. INSTALL FRONT FENDER SIDE PANEL PROTECTOR LH
  1. Attach the 4 clips and 2 guides to install the fender side panel.


14. INSTALL FRONT FENDER SIDE PANEL PROTECTOR RH

HINT:
Use the same procedure described for the LH side.


15. INSTALL UPPER RADIATOR SUPPORT SEAL
  1. Install the upper radiator support seal with the 13 clips.


16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

← INSTALLATION (Aug 2013 – Jul 2014)COMPONENTS (from Aug 2013) →