2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.


3. REMOVE FRONT FENDER SIDE PANEL PROTECTOR LH

  1. E199696
    Detach the 3 clips and guide, and remove the front fender side panel protector.


4. REMOVE FRONT FENDER SIDE PANEL PROTECTOR RH

HINT:
Use the same procedure for the RH side and LH side.


5. REMOVE FRONT FENDER TO COWL SIDE SEAL LH

  1. E198988
    Detach the 5 claws and remove the front fender to cowl side seal LH.


6. REMOVE FRONT FENDER TO COWL SIDE SEAL RH

HINT:
Use the same procedure for the RH side and LH side.


7. REMOVE WINDSHIELD WIPER ARM COVER

  1. E198979E01
    Using a screwdriver, detach the 3 claws and remove the wiper arm cover.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    1. Tape the screwdriver tip before use.
    2. Use the same procedure for the RH and LH sides.


8. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E197606
    Remove the nut and front wiper arm and blade assembly LH.


9. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

  1. E197608
    Remove the nut and front wiper arm and blade assembly RH.


10. REMOVE HOOD TO COWL TOP SEAL

  1. E197610
    Detach the 7 claws and 2 clips and remove the hood to cowl top seal.


11. REMOVE CENTER NO. 2 COWL TOP VENTILATOR LOUVER

  1. E197612
    Detach the 2 claws and 3 guides and remove the center No. 2 cowl top ventilator louver.


12. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E197614E01
    Remove the 2 clips.

  1. Detach the 6 claws and guide (A).

    Text in Illustration 
    *1
    Guide A
    *2
    Guide B

  1. Disengage the 10 guides (B) and pull out the cowl top ventilator louver sub-assembly.


13. REMOVE WINDSHIELD WIPER MOTOR AND LINK

  1. E197616
    Detach the clamp and disconnect the connector.

  1. E197618
    Remove the 2 bolts.

  1. E197620E01
    Detach the grommet and remove the windshield wiper motor and link as shown in the illustration.
    Text in Illustration 
    *1
    Grommet

    NOTICE:
    Be careful not to damage the windshield when removing the windshield wiper motor and link assembly.


14. REMOVE FRONT WIPER CRANK SUB-ASSEMBLY (for RHD, w/ Spring)

  1. E201892E01
    Using a screwdriver, separate the windshield wiper link rod from the crank arm pivot of the front wiper crank sub-assembly as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. E201895
    Remove the nut and front wiper crank sub-assembly.


15. REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY

  1. w/o Spring:

    1. E197622E01
      Using a screwdriver, separate the windshield wiper link rod from the crank arm pivot of the front wiper crank as shown in the illustration.
      Text in Illustration 
      *1
      Protective Tape

      HINT:
      Tape the screwdriver tip before use.

  1. E197625
    Disconnect the connector.

  1. Using a T30 ''TORX'' socket, remove the 2 bolts and windshield wiper motor.


16. REMOVE WIPER MOTOR WIRE

  1. E197627
    Detach the claw and remove the wiper motor wire.

← REMOVAL (Aug 2013 – Jul 2014)INSPECTION (from Aug 2013) →