2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

ECM Communication Stop Mode

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Detection Item
Symptom
Trouble Area
ECM Communication Stop Mode
Either condition is met:
  1. "ECM (Engine)" is not displayed on "Bus Check".
  2. "ECM Communication Stop Mode" in "DTC Combination Table" applies.
  1. Power source or inside ECM
  2. ECM

WIRING DIAGRAM

C217303E01
C217303E03

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)

  1. for 1GR-FE:

    1. Connect the cable to the negative (-) battery terminal.C217328E04

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to ECM)
      -
      -

    2. Disconnect the C36, C37 and G55 ECM connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      C36-12 (E1) - Body ground
      Always
      Below 1 Ω
      C37-14 (E01) - Body ground
      Always
      Below 1 Ω
      C37-15 (E02) - Body ground
      Always
      Below 1 Ω
      C37-10 (ME01) - Body ground
      Always
      Below 1 Ω
      G55-12 (EC) - Body ground
      Always
      Below 1 Ω

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      G55-24 (BATT) - Body ground
      Always
      11 to 14 V
      G55-23 (+B2) - Body ground
      Battery positive (+) voltage applied to terminal G55-9 (MREL)
      11 to 14 V
      G55-22 (+B) - Body ground
      Battery positive (+) voltage applied to terminal G55-9 (MREL)
      11 to 14 V

  1. for 1KD-FTV:

    1. Connect the cable to the negative (-) battery terminal.C289505E01

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to ECM)
      -
      -

    2. Disconnect the G57, G58 and C93 ECM connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      C93-1 (E1) - Body ground
      Always
      Below 1 Ω
      C93-12 (E01) - Body ground
      Always
      Below 1 Ω
      C93-13 (E02) - Body ground
      Always
      Below 1 Ω
      C93-8 (ME01) - Body ground
      Always
      Below 1 Ω
      G57-11 (EC) - Body ground
      Always
      Below 1 Ω

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      G57-23 (BATT) - Body ground
      Always
      11 to 14 V
      G57-17 (+B2) - Body ground
      Battery positive (+) voltage applied to terminal G58-11 (MREL)
      11 to 14 V
      G57-24 (+B) - Body ground
      Battery positive (+) voltage applied to terminal G58-11 (MREL)
      11 to 14 V

Result 
Result
Proceed to
OK (for 1GR-FE)
A
OK (for 1KD-FTV)
B
NG
C


B
REPLACE ECM (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE ECM (Click here)


← Yaw Rate Sensor Communication Stop Mode (from Aug 2014)ECM Communication Stop Mode (from Aug 2014) →