2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

Main Body ECU Communication Stop Mode

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Detection Item
Symptom
Trouble Area
Main Body ECU Communication Stop Mode
Either condition is met:
  1. "Main Body" is not displayed on "Bus Check".
  2. "Main Body ECU Communication Stop Mode" in "DTC Combination Table" applies.
  1. Power source or inside main body ECU (multiplex network body ECU)
  2. Main body ECU (multiplex network body ECU) CAN branch wire or connector
  3. Main body ECU (multiplex network body ECU)

WIRING DIAGRAM

C217717E09

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU CAN BRANCH WIRE)

  1. C212975E08
    Disconnect the G64 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G64-14 (CANH) - G64-13 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Main Body ECU [Multiplex Network Body ECU])



NG
REPAIR OR REPLACE MAIN BODY ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)

  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

    C215398E08
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Main Body ECU [Multiplex Network Body ECU])
    *b
    Front view of wire harness connector
    (to Main Body ECU [Multiplex Network Body ECU])

  1. Remove the main body ECU (multiplex network body ECU) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G63-2 (GND2) - Body ground
    Always
    Below 1 Ω
    A-11 (GND1) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A-31 (ALTB) - Body ground
    Always
    11 to 14 V
    A-30 (BECU) - Body ground
    Always
    11 to 14 V
    A-29 (ACC) - Body ground
    Engine switch on (ACC)
    11 to 14 V
    A-32 (IG) - Body ground
    Engine switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)


← Main Body ECU Communication Stop Mode (Aug 2013 – Jul 2014)Power Management Control ECU Communication Stop Mode (Aug 2013 – Jul 2014) →