2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

DATA LIST / ACTIVE TEST

System information · Vehicles built from Aug 2013


READ DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Immobiliser / Data List.

  5. According to the display on the intelligent tester, read the Data List.

    Immobiliser 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door Courtesy SW*1
    Driver side door courtesy light switch / ON or OFF
    ON: Driver side door open
    OFF: Driver side door closed
    -
    Key SW
    Unlock warning switch signal / ON or OFF
    ON: Key inserted in ignition key cylinder
    OFF: No key in ignition key cylinder
    -
    IG SW
    Ignition switch signal / ON or OFF
    ON: Ignition switch ON
    OFF: Ignition switch ACC or off
    -
    Immobiliser
    Immobiliser system status / Set or Unset
    Set: No key in ignition key cylinder
    Unset: Key inserted in ignition key cylinder
    -
    Permit (Start)*2
    Permit (start) signal / OK or NG
    OK: Engine start permitted
    NG: Engine start not permitted
    -
    Response
    Transponder chip data / OK or NG
    OK: Data OK
    NG: Data error
    -
    Frame Error
    Transponder chip data / OK or NG
    OK: Data OK
    NG: Data error
    -
    Different Serial Number
    Transponder chip data / OK or NG
    OK: Data OK
    NG: Data error
    -
    Different Encrypt Code
    Transponder chip data / OK or NG
    OK: Data OK
    NG: Data error
    -
    Abnormal Status
    Transponder chip data / OK or NG
    OK: Data OK
    NG: Data error
    -
    BCC Malfunction
    Transponder chip signal / OK or NG
    OK: Correct data sent
    NG: Incorrect data sent
    -
    Sub Key
    Sub-key code signal / Reg or Unreg
    Reg: Registered sub-key code sent
    Unreg: Unmatching sub-key code sent
    -
    Master Key
    Master key code signal / Reg or Unreg
    Reg: Registered master key code sent
    Unreg: Unmatching master key code sent
    -
    Transponder S-code
    Number of registered sub-keys / min.: 0, max.: 3
    Number of registered sub-keys
    -
    Transponder M-code
    Number of registered master keys / min.: 0, max.: 5
    Number of registered master keys
    -
    Reg Code Space Full
    Key registration code memory space full / Yes or No
    No: Possible to register more key codes
    Yes: Cannot register any more key codes
    -
    +B
    +B judgment / Normal or Break
    Normal: Battery power supply normal
    Break: Battery power supply malfunctioning
    -
    Antenna Coil Status
    Antenna coil condition / Normal or Fail
    Normal: Antenna coil normal
    Fail: Antenna coil malfunctioning
    -
    EEPROM Status*1
    EEPROM status / OK or NG
    OK: Data OK
    NG: Data error
    -
    E/G Start Permission*1
    Engine start permission / OK or NG
    OK: Engine start permitted
    NG: Engine start not permitted
    -
    Immobi ECU Comm Spd*1
    Immobiliser ECU communication speed / Unknown, 50bps, 200bps or No Res
    Unknown: ECU communication speed unknown
    50bps: ECU communication speed 50 bps
    200bps: ECU communication speed 200 bps
    No Res: ECU communication speed no response
    -
    The Number of DTCs*1
    Number of DTCs / Min.: 0, Max.: 255
    Number of stored DTCs
    -
    1. *1: except 5L-E
    2. *2: for 5L-E


PERFORM ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Immobiliser / Active Test.

  5. According to the display on the intelligent tester, perform the Active Test.

    Immobiliser 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Security Indicator
    Security indicator light
    ON/OFF
    The test is possible when the following conditions are met:
    1. The key is in the ignition key cylinder.

← DTC CHECK / CLEAR (from Aug 2013)DIAGNOSTIC TROUBLE CODE CHART (Aug 2013 – Jul 2014) →