2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Only Wireless Control Function is Inoperative

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. The main body ECU then controls all the doors by sending lock/unlock signals to each door.

WIRING DIAGRAM

B242194E02

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. When replacing the door control receiver, refer to the registration procedures (Click here).


1. CHECK POWER DOOR LOCK OPERATION
  1. Check the power door lock operation (Click here).

    OK:
    Each door locks and unlocks normally.



NG
Go to POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2. CHECK KEY REMINDER WARNING OPERATION
  1. Check the key reminder buzzer operation (Click here).

    HINT:
    If the key reminder buzzer is functioning normally, it can be assumed that the unlock warning switch is also functioning normally.

    OK:
    Key reminder buzzer operates normally.



NG
Go to KEY REMINDER WARNING SYSTEM (Click here)
OK


3. CHECK WIRELESS DOOR CONTROL TRANSMITTER
  1. Check whether the wireless door lock control functions operate normally with another registered transmitter.

    OK:
    Wireless door lock control functions operate normally.



NG
Go to step 5
OK


4. CHECK TRANSMITTER BATTERY
  1. Remove the battery from the inoperative wireless door control transmitter (Click here).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Battery positive (+) - Battery negative (-)
    Always
    2.5 to 3.2 V



NG
REPLACE TRANSMITTER BATTERY (Click here)
OK

REPLACE DOOR CONTROL TRANSMITTER

5. CHECK FOR ELECTRICAL NOISE
  1. Move the transmitter in the vicinity of the door control receiver.

    HINT:
    Refer to Parts Location for the location of the door control receiver (Click here).

  1. Press and hold either the lock or unlock transmitter switch for 1 second, and check that the doors are locked or unlocked accordingly.

    OK:
    Wireless door lock control functions operate normally.

    HINT:
    1. Check if electrical noise is the cause by moving the door control transmitter closer to the door control receiver. Moving closer will decrease the effects of electrical noise.
    2. If the operation check can be performed normally, there is a high probability that electrical noise or a decrease in output from the door control transmitter is the cause of the malfunction. There is a high probability that electrical noise is the cause if the problem occurs only in a certain location or only during a certain time of day. Also, custom components may be causing electrical noise. If custom components are installed in the vehicle, remove them and perform the operation check again.



NG
Go to step 6
OK

FIND CAUSE OF ELECTRICAL NOISE AND REMOVE IT

6. CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - MAIN BODY ECU)
  1. Disconnect the R26 receiver connector.

  1. Disconnect the G64 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R26-2 (RDA) - G64-26 (RDA)
    Always
    Below 1 Ω
    R26-3 (PRG) - G64-25 (PRG)
    R26-2 (RDA) or G64-26 (RDA) - Body ground
    Always
    10 kΩ or higher
    R26-3 (PRG) or G64-25 (PRG) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)

  1. B219541E05
    Disconnect the R26 receiver connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R26-1 (GND) - Body ground
    Always
    Below 1 Ω

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    R26-5 (+B) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Door Control Receiver)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. CHECK DOOR CONTROL RECEIVER (OUTPUT)

  1. E146641E07
    Using an oscilloscope, check the waveform.
    Measurement Condition 
    Item
    Content
    Tester Connection
    R26-2 (RDA) - Body ground
    Tool Setting
    10 V/DIV., 50 μs/DIV.
    Condition
    No key in ignition key cylinder, all doors closed and transmitter switch off → on

    OK:
    Waveform is output normally (refer to illustration).

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 5 Door)
    B
    NG (for 3 Door)
    C



B
REPLACE DOOR CONTROL RECEIVER (Click here)

C
REPLACE DOOR CONTROL RECEIVER (Click here)
A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)


← Only Wireless Control Function is Inoperative (Aug 2013 – Jul 2014)No Answer-Back (Aug 2013 – Jul 2014) →