Speaker Circuit
Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The sound signals amplified by the radio receiver assembly are sent to the speakers from the radio receiver assembly via the speaker circuit.If there is a short in a speaker circuit, the radio receiver assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is not a malfunction in the radio receiver assembly or speakers.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT) |
- *1: for RH Side
- *2: for LH Side
Disconnect the H27 and H46 radio receiver assembly connectors.
Disconnect the J4*1 and/or K3*2 front No. 1 speaker assembly connector.
Disconnect the H34*1 and/or H35*2 front No. 2 speaker assembly connector.
for 3 Door:Disconnect the Q32*1 and/or R37*2 rear speaker set connector.
for 5 Door:Disconnect the L1*1 and/or M1*2 rear speaker set connector.
- Standard Resistance:
for 3 Door (RH Side) Tester Connection
Condition
Specified Condition
H46-1 (FR+) - H34-3 (TWR+)
Always
Below 1 Ω
H46-5 (FR-) - H34-1 (TWR-)
Always
Below 1 Ω
H34-4 (+) - J4-1
Always
Below 1 Ω
H34-2 (-) - J4-2
Always
Below 1 Ω
H27-1 (RR+) - Q32-1
Always
Below 1 Ω
H27-3 (RR-) - Q32-2
Always
Below 1 Ω
H46-1 (FR+) - Body ground
Always
10 kΩ or higher
H46-5 (FR-) - Body ground
Always
10 kΩ or higher
H34-4 (+) - Body ground
Always
10 kΩ or higher
H34-2 (-) - Body ground
Always
10 kΩ or higher
H27-1 (RR+) - Body ground
Always
10 kΩ or higher
H27-3 (RR-) - Body ground
Always
10 kΩ or higher
for 3 Door (LH Side) Tester Connection
Condition
Specified Condition
H46-2 (FL+) - H35-3 (TWL+)
Always
Below 1 Ω
H46-6 (FL-) - H35-1 (TWL-)
Always
Below 1 Ω
H35-4 (+) - K3-1
Always
Below 1 Ω
H35-2 (-) - K3-2
Always
Below 1 Ω
H27-2 (RL+) - R37-1
Always
Below 1 Ω
H27-6 (RL-) - R37-2
Always
Below 1 Ω
H46-2 (FL+) - Body ground
Always
10 kΩ or higher
H46-6 (FL-) - Body ground
Always
10 kΩ or higher
H35-4 (+) - Body ground
Always
10 kΩ or higher
H35-2 (-) - Body ground
Always
10 kΩ or higher
H27-2 (RL+) - Body ground
Always
10 kΩ or higher
H27-6 (RL-) - Body ground
Always
10 kΩ or higher
for 5 Door (RH Side) Tester Connection
Condition
Specified Condition
H46-1 (FR+) - H34-3 (TWR+)
Always
Below 1 Ω
H46-5 (FR-) - H34-1 (TWR-)
Always
Below 1 Ω
H34-4 (+) - J4-1
Always
Below 1 Ω
H34-2 (-) - J4-2
Always
Below 1 Ω
H27-1 (RR+) - L1-1
Always
Below 1 Ω
H27-3 (RR-) - L1-2
Always
Below 1 Ω
H46-1 (FR+) - Body ground
Always
10 kΩ or higher
H46-5 (FR-) - Body ground
Always
10 kΩ or higher
H34-4 (+) - Body ground
Always
10 kΩ or higher
H34-2 (-) - Body ground
Always
10 kΩ or higher
H27-1 (RR+) - Body ground
Always
10 kΩ or higher
H27-3 (RR-) - Body ground
Always
10 kΩ or higher
for 5 Door (LH Side) Tester Connection
Condition
Specified Condition
H46-2 (FL+) - H35-3 (TWL+)
Always
Below 1 Ω
H46-6 (FL-) - H35-1 (TWL-)
Always
Below 1 Ω
H35-4 (+) - K3-1
Always
Below 1 Ω
H35-2 (-) - K3-2
Always
Below 1 Ω
H27-2 (RL+) - M1-1
Always
Below 1 Ω
H27-6 (RL-) - M1-2
Always
Below 1 Ω
H46-2 (FL+) - Body ground
Always
10 kΩ or higher
H46-6 (FL-) - Body ground
Always
10 kΩ or higher
H35-4 (+) - Body ground
Always
10 kΩ or higher
H35-2 (-) - Body ground
Always
10 kΩ or higher
H27-2 (RL+) - Body ground
Always
10 kΩ or higher
H27-6 (RL-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 2. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
Remove the front No. 1 speaker assembly LH and/or RH (Click here).
Inspect the front No. 1 speaker assembly LH and/or RH (Click here).
|
|
||||
| OK | |
| 3. CHECK FRONT NO. 2 SPEAKER ASSEMBLY |
Replace the front No. 2 speaker LH and/or RH with a known good one (Click here).
Check that the malfunction disappears.
- HINT:
- Connect all the connectors that were disconnected from the front No. 2 speaker assemblies.
- When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
- Perform the above inspection on both LH and RH sides.
- Connect all the connectors that were disconnected from the front No. 2 speaker assemblies.
- OK:
- Malfunction disappears.
|
|
||||
| OK | ||
| ||
| 4. INSPECT REAR SPEAKER SET |
Remove the rear speaker set LH and/or RH (Click here).
Inspect the rear speaker set LH and/or RH (Click here).
|
|
||||
| OK | ||
| ||
