2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

INSPECTION

Inspection · Vehicles built from Aug 2013


INSPECT REAR DOOR LOCK ASSEMBLY LH (w/o Double Locking System)

B184440E07
Text in Illustration 
*a
Lock
*b
Unlock
*c
Component without harness connected
(Rear Door Lock assembly LH)
-
-
  1. Check the door lock motor operation.

    1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 4 (L)
      Battery negative (-) → 1 (UL)
      Lock
      Battery positive (+) → 1 (UL)
      Battery negative (-) → 4 (L)
      Unlock

      1. If the result is not as specified, replace the rear door lock assembly.

  1. Check the detection switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      6 (LSSR) - 9 (E)
      Unlock
      Below 1 Ω
      6 (LSSR) - 9 (E)
      Lock
      10 kΩ or higher

      1. If the result is not as specified, replace the rear door lock assembly.


INSPECT REAR DOOR LOCK ASSEMBLY LH (w/ Double Locking System)

B144119E08
Text in Illustration 
*a
Lock
*b
Unlock
*c
Component without harness connected
(Rear Door Lock Assembly LH)
-
-
  1. Check the door lock motor operation.

    1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 2 (L)
      Battery negative (-) → 1 (UL)
      Lock
      Battery positive (+) → 1 (UL)
      Battery negative (-) → 2 (L)
      Unlock
      Battery positive (+) → 4 (DL)
      Battery negative (-) → 3 (UNDL)
      Set
      Battery positive (+) → 3 (UNDL)
      Battery negative (-) → 4 (DL)
      Unset

      1. If the result is not as specified, replace the rear door lock assembly.

  1. Check the detection switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      5 (LSSR) - 6 (E)
      Unlock
      Below 1 Ω
      5 (LSSR) - 6 (E)
      Lock
      10 kΩ or higher

      1. If the result is not as specified, replace the rear door lock assembly.


INSPECT REAR DOOR LOCK ASSEMBLY RH (w/o Double Locking System)

B184441E06
Text in Illustration 
*a
Unlock
*b
Lock
*c
Component without harness connected
(Rear Door Lock Assembly RH)
-
-
  1. Check the door lock motor operation.

    1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 4 (L)
      Battery negative (-) → 1 (UL)
      Lock
      Battery positive (+) → 1 (UL)
      Battery negative (-) → 4 (L)
      Unlock

      1. If the result is not as specified, replace the rear door lock assembly.

  1. Check the detection switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      6 (LSSR) - 9 (E)
      Unlock
      Below 1 Ω
      6 (LSSR) - 9 (E)
      Lock
      10 kΩ or higher

      1. If the result is not as specified, replace the rear door lock assembly.


INSPECT REAR DOOR LOCK ASSEMBLY RH (w/ Double Locking System)

B144120E08
Text in Illustration 
*a
Unlock
*b
Lock
*c
Component without harness connected
(Rear Door Lock Assembly RH)
-
-
  1. Check the door lock motor operation.

    1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 4 (L)
      Battery negative (-) → 3 (UL)
      Lock
      Battery positive (+) → 3 (UL)
      Battery negative (-) → 4 (L)
      Unlock
      Battery positive (+) → 2 (DL)
      Battery negative (-) → 1 (UNDL)
      Set
      Battery positive (+) → 1 (UNDL)
      Battery negative (-) → 2 (DL)
      Unset

      1. If the result is not as specified, replace the rear door lock assembly.

  1. Check the detection switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      9 (LSSR) - 10 (E)
      Unlock
      Below 1 Ω
      9 (LSSR) - 10 (E)
      Lock
      10 kΩ or higher

      1. If the result is not as specified, replace the rear door lock assembly.

← REMOVAL (from Aug 2014)INSTALLATION (Aug 2013 – Jul 2014) →