2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH

  1. B239600
    Using moulding remover A, detach the 3 claws and remove the rear door inside handle bezel as shown in the illustration.


3. REMOVE ASSIST GRIP COVER LH

  1. B239602
    Using moulding remover A, detach the 8 claws and remove the assist grip cover.


4. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B239604
    Remove the 3 screws.

  1. Using a clip remover, detach the 9 clips.

  1. B239606
    Pull out the rear door trim board sub-assembly in the direction indicated by the arrow in the illustration.

  1. Raise the rear door trim board sub-assembly to detach the 4 claws and remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.

  1. B239612
    Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly as shown in the illustration.

  1. B239616E02
    Disconnect each connector.
    Text in Illustration 
    *A
    for 14 Speakers
    *B
    for 9 Speakers

  1. B241320
    Using a screwdriver, detach the claw and remove the clamp.


5. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH

  1. B239615
    Using a screwdriver, detach the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.


6. REMOVE REAR DOOR SERVICE HOLE COVER LH

  1. B239620
    Disconnect the connector.

  1. Detach the 3 clamps, move the wire harness out of the way and remove the service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.


7. REMOVE REAR DOOR GLASS RUN LH

  1. B239628
    Remove the rear door glass run.


8. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

  1. B239630E01
    Loosen the temporary bolt.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Remove the 2 bolts and screw.

  1. Remove the rear door window division bar sub-assembly.

  1. Remove the temporary bolt from the rear door window division bar sub-assembly.


9. REMOVE REAR DOOR QUARTER WINDOW GLASS LH

  1. B239632
    Remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit as shown in the illustration.


10. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH
  1. Connect the cable to the negative (-) battery terminal and rear power window regulator motor connector.

  1. Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the power window regulator switch assembly and rear power window regulator motor connectors.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. B239636
    Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    After the bolts are removed, do not allow the door glass to fall.

  1. B239640E01
    Remove the rear door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the door glass.


11. REMOVE REAR DOOR LOCK ASSEMBLY LH

  1. B237876E01
    Using a T30 "TORX" wrench, remove the 3 screws.
    Text in Illustration 
    *A
    w/o Double Locking System
    *B
    w/ Double Locking System
    V100135
    Slide

  1. Move the rear door lock assembly downward, pull the release plate out of the rear door outside handle frame, and remove the rear door lock assembly and cables as a unit.

  1. Remove the door lock wiring harness seal from the rear door lock assembly.


12. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

  1. B239650E03
    Using a screwdriver, detach the claw.
    Text in Illustration 
    *A
    w/ Double Locking System
    *B
    w/o Double Locking System

    HINT:
    Tape the screwdriver tip before use.

  1. B239652E04
    Remove the rear door lock remote control cable assembly.
    Text in Illustration 
    *A
    w/ Double Locking System
    *B
    w/o Double Locking System


13. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

  1. B239654E03
    Using a screwdriver, detach the 3 claws.
    Text in Illustration 
    *A
    w/ Double Locking System
    *B
    w/o Double Locking System

    HINT:
    Tape the screwdriver tip before use.

  1. B239656E02
    Remove the rear door inside locking cable assembly.
    Text in Illustration 
    *A
    w/ Double Locking System
    *B
    w/o Double Locking System

← REMOVAL (Aug 2013 – Jul 2014)INSPECTION (from Aug 2013) →