Back Door Entry Lock Function does not Operate
Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
If the back door entry lock function does not operate but the back door unlock function operates, the communication line between the vehicle and electrical key transmitter is normal. The entry lock switch circuit (luggage electrical key switch → certification ECU) may be faulty.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
- When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
- Check that there are no electrical key transmitters in the vehicle.
- When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.
- Before replacing the certification ECU, refer to the Service Bulletin.
- The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
| 1. CHECK POWER DOOR LOCK OPERATION |
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (Click here).
- OK:
- Door locks operate normally.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
Main Body Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Back Door Lock Pos SW
Back door lock position switch status / ON or OFF
ON: Back door unlocked
OFF: Back door locked
-
- OK:
- On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
|
|
||||
| OK | |
| 3. READ VALUE USING INTELLIGENT TESTER (LOCK SWITCH) |
Using the intelligent tester, read the Data List (Click here).
Entry&Start Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Tr/B-Door Lock SW
Back door lock switch / ON or OFF
ON: Back door lock switch pushed
OFF: Back door lock switch not pushed
-
- OK:
- "ON" (lock switch is pushed) and "OFF" (lock switch is not pushed) appear on the screen.
|
|
||||
| OK | ||
| ||
| 4. INSPECT LUGGAGE ELECTRICAL KEY SWITCH (LOCK SWITCH) |
![]() ![]() |
Remove the luggage electrical key switch (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
2 (L) - 3 (B)
No switch pushed
10 kΩ or higher
2 (L) - 3 (B)
Lock switch pushed
Below 1 Ω
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (LUGGAGE ELECTRICAL KEY SWITCH - CERTIFICATION ECU) |
Disconnect the X6 switch connector.
Disconnect the G38 ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
X6-2 (L) - G38-23 (TSW6)
Always
Below 1 Ω
G38-23 (TSW6) - Body ground
Always
10 kΩ or higher
X6-3 (B) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||

