2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

REMOVAL

Removal / installation · Vehicles built from Aug 2013


1. REMOVE BACK DOOR CENTER GARNISH

  1. B239438
    Detach the 4 clips and remove the back door center garnish.


2. REMOVE BACK DOOR SIDE GARNISH LH

  1. B239439
    Detach the 2 clips and claw and remove the back door side garnish.


3. REMOVE BACK DOOR SIDE GARNISH RH

  1. B239440
    Detach the 2 clips and claw and remove the back door side garnish.


4. REMOVE BACK DOOR TRIM COVER

  1. B239441
    Remove the back door trim cover as shown in the illustration.


5. REMOVE UPPER TOOL BOX PANEL SUB-ASSEMBLY

  1. B239442
    Remove the upper tool box panel sub-assembly as shown in the illustration.


6. REMOVE TOOL CASE

  1. B239445
    Detach the 2 claws and remove the tool case.


7. REMOVE BACK DOOR INSIDE HANDLE BEZEL (for Face to Face Seat Type)

  1. B239466
    Remove the screw.

  1. Detach the 5 claws and remove the back door inside handle bezel.


8. REMOVE BACK DOOR TRIM PANEL ASSEMBLY

  1. B241516
    Detach the claw and remove the cover.

    HINT:
    Tape the screwdriver tip before use.

  1. B239444
    Remove the screw.

  1. w/o Back Door Tire Carrier:

    1. B239446
      Remove the bolt.

    2. Detach the 15 clips and remove the back door trim panel assembly.

  1. w/ Back Door Tire Carrier:

    1. B239447
      Remove the bolt.

    2. Detach the 16 clips and remove the back door trim panel assembly.

  1. for Face to Face Seat Type:

    1. B241528
      Remove the screw and bolt.

    2. Detach the 15 clips and remove the back door trim panel assembly.


9. REMOVE BACK DOOR INSIDE HANDLE SUB-ASSEMBLY (for Face to Face Seat Type)

  1. B239467
    Detach the guide.

  1. Detach the claws and remove the inside handle sub-assembly.

  1. Disconnect the 2 cables from the inside handle sub-assembly.


10. REMOVE SPARE WHEEL COVER PAD

  1. B239475
    Detach the 7 claws and move the wheel cover pad out of the way.


11. REMOVE SPARE WHEEL COVER

  1. B241517
    Remove the bolt.

  1. Move the lever.

  1. B239474
    Detach the 8 claws and remove the spare wheel cover.


12. REMOVE SPARE TIRE

13. REMOVE NO. 2 SPARE WHEEL COVER

  1. B239476
    Remove the 4 screws and No. 2 spare wheel cover.


14. REMOVE REAR SPOILER COVER RH

B247537E01
  1. Detach the fastening tape and 5 clips and remove the rear No. 1 spoiler cover.

    Text in Illustration 
    *1
    Fastening Tape


15. REMOVE REAR SPOILER SUB-ASSEMBLY
  1. w/o Back Door Tire Carrier:
    Remove the rear spoiler sub-assembly (Click here).

  1. w/ Back Door Tire Carrier:
    Remove the rear spoiler sub-assembly (Click here).


16. REMOVE REAR WIPER ARM

  1. E197697
    Remove the nut and rear wiper arm.


17. REMOVE REAR WIPER MOTOR ASSEMBLY

  1. E197698E01
    Disconnect the washer hose and wiper motor connector.
    Text in Illustration 
    *A
    w/ Back Door Tire Carrier
    *B
    w/o Back Door Tire Carrier

  1. E197701E01
    Remove the 3 bolts.
    Text in Illustration 
    *A
    w/ Back Door Tire Carrier
    *B
    w/o Back Door Tire Carrier

  1. Detach the 2 guides and remove the rear wiper motor.


18. REMOVE NO. 1 BACK WINDOW WIPER MOTOR BRACKET

  1. B239460
    Using a clip remover, detach the clamp.

  1. Remove the 3 bolts.

  1. Using a clip remover, detach the 2 clips and remove the No. 1 back window wiper motor bracket.


19. REMOVE BACK WINDOW OUTSIDE MOULDING

  1. Using a knife, cut off the 2 outside mouldings as shown in the illustration.

    NOTICE:
    1. Do not damage the vehicle body with the knife.
    2. If the vehicle body is damaged, repair the damaged portion by applying an anti-rust coating after removing the back window glass assembly.


    B239012E01
    Text in Illustration 
    *1
    Cut
    -
    -

  1. Remove the remaining outside moulding from the back door glass.


20. REMOVE BACK DOOR GLASS

B239013E01
  1. Apply protective tape to the outer surface of the vehicle body to prevent scratches.

    NOTICE:
    When separating the back window glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

    Text in Illustration 
    *1
    Protective Tape

  1. Disconnect the connectors.

  1. B239014E01
    From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.
    Text in Illustration 
    *1
    Clip
    *2
    Adhesive Dam

  1. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

  1. Cut off the adhesive by pulling the piano wire around the back window glass.

    NOTICE:
    1. When separating the glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.
    2. Leave as much adhesive on the vehicle body as possible when removing the back window glass.

  1. B239015E01
    Place matchmarks over the glass and vehicle body at the locations indicated in the illustration.

    HINT:
    Matchmarks do not need to be placed if the glass is not going to be reused.

    Text in Illustration 
    *a
    Matchmark

  1. B239016
    Using suction cups, remove the back door glass.

    NOTICE:
    Be careful not to drop the back door glass.


21. REMOVE BACK WINDOW GLASS CLIP LH

  1. B239018
    Using a scraper, remove the clip.

    NOTICE:
    1. Be careful not to damage the back door glass.
    2. Be sure to replace the clip with new one.


22. REMOVE BACK WINDOW GLASS CLIP RH

  1. B239017
    Using a scraper, remove the clip.

    NOTICE:
    1. Be careful not to damage the back door glass.
    2. Be sure to replace the clip with new one.


23. REMOVE BACK DOOR GLASS ADHESIVE DAM

  1. B239019
    Using a scraper, remove the 2 dams.

    NOTICE:
    1. Be careful not to damage the back door glass.
    2. Be sure to replace the 2 dams with new ones.


24. REMOVE BACK WINDOW UPPER OUTSIDE MOULDING

  1. B242872E01
    Using a scraper, remove the outside moulding LH and RH.

    NOTICE:
    1. Be careful not to damage the back door glass.
    2. Be sure to replace the mouldings with new ones.

    Text in Illustration 
    *1
    Back Window Upper Outside Moulding LH
    *2
    Back Window Upper Outside Moulding RH

← COMPONENTS (from Aug 2013)INSTALLATION (from Aug 2013) →