2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built from Aug 2013


1. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.


2. REMOVE FRONT BUMPER COVER LOWER
  1. Remove the clip, 5 bolts and front bumper cover lower.


3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts.

  1. A224743
    Unhook the engine under cover from the vehicle body as shown in the illustration.


4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


A273797E01
Text in Illustration 
*1
Reservoir Cap
*2
Radiator Cap
*3
Radiator Drain Cock Plug
*4
Cylinder Block Drain Cock Plug
  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap and drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the cylinder block drain cock plug and drain the coolant from the engine.


5. REMOVE V-BANK COVER

  1. A229925E01
    Raise the front of the V-bank cover to detach the 2 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
    Text in Illustration 
    *1
    Pin
    *2
    Hook


6. REMOVE FRONT BUMPER COVER
  1. Remove the front bumper cover (Click here).


7. REMOVE UPPER FRONT BUMPER RETAINER

  1. A302327
    Remove the 3 bolts and retainer.


8. REMOVE RADIATOR SIDE DEFLECTOR RH

  1. A302328
    Using a clip remover, detach the 3 claws and remove the clip. Then move the side deflector so that the radiator can be removed in the step below.


9. REMOVE RADIATOR SIDE DEFLECTOR LH

  1. A302329
    Using a clip remover, detach the 3 claws and remove the clip. Then move the side deflector so that the radiator can be removed in the step below.


10. REMOVE NO. 1 RADIATOR HOSE

A223076

11. REMOVE NO. 2 RADIATOR HOSE

  1. A223077
    Disconnect the radiator hose from the water inlet.

  1. A223078
    Detach the clamp and remove the radiator hose.


12. REMOVE RADIATOR RESERVOIR

  1. A223079
    Disconnect the reservoir hose from the upper side of the radiator tank.

  1. Remove the 3 bolts and radiator reservoir.


13. DISCONNECT OIL COOLER TUBE (w/ Warmer)

  1. A223080
    Detach the claw to open the flexible hose clamp, and then remove the 2 bolts to disconnect the oil cooler tube from the fan shroud.


14. DISCONNECT OIL COOLER TUBE (w/ Air Cooled Transmission Oil Cooler)

  1. A223081
    Detach the claw to open the flexible hose clamp, and then remove the 2 bolts to disconnect the oil cooler tube from the fan shroud.


15. REMOVE FAN SHROUD

  1. A223082
    Loosen the 4 nuts holding the fluid coupling fan.

  1. Remove the fan and generator V-belt (Click here).

  1. A223083
    Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the water pump.


16. REMOVE RADIATOR ASSEMBLY

  1. A223084E01
    for Automatic Transmission:
    Disconnect the 2 oil cooler hoses.
    Text in Illustration 
    *A
    w/ Warmer
    *B
    w/ Air Cooled Transmission Oil Cooler

  1. A223085
    Remove the 4 bolts and radiator.


17. REMOVE NO. 1 RADIATOR TO SUPPORT SEAL
  1. Remove the seal from the radiator assembly.


18. REMOVE NO. 2 RADIATOR TO SUPPORT SEAL
  1. Remove the seal from the radiator assembly.

← ON-VEHICLE INSPECTION (from Aug 2013)INSTALLATION (from Aug 2013) →