2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Back Door Entry Unlock Function does not Operate

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

If the back door entry unlock function does not operate but the back door lock function operates, the communication line between the vehicle and electrical key transmitter is normal. The entry unlock switch circuit (luggage electrical key switch → certification ECU) may be faulty.

WIRING DIAGRAM

B242195E04

INSPECTION PROCEDURE

NOTICE:
  1. The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
  3. Check that there are no electrical key transmitters in the vehicle.
  4. When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.
  5. Before replacing the certification ECU, refer to the Service Bulletin.


1. CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (Click here).

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Back Door Lock Pos SW
    Back door lock position switch status / ON or OFF
    ON: Back door unlocked
    OFF: Back door locked
    -

    OK:
    On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Back Door Lock/Unlock Functions do not Operate) (Click here)
OK


3. READ VALUE USING INTELLIGENT TESTER (UNLOCK SWITCH)
  1. Using the intelligent tester, read the Data List (Click here).

    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Tr/B Door Unlock SW
    Back door unlock switch / ON or OFF
    ON: Back door unlock switch pushed
    OFF: Back door unlock switch not pushed
    -

    OK:
    "ON" (unlock switch is pushed) and "OFF" (unlock switch is not pushed) appear on the screen.



NG
Go to step 4
OK

REPLACE CERTIFICATION ECU

4. INSPECT LUGGAGE ELECTRICAL KEY SWITCH (UNLOCK SWITCH)
E139345E13
  1. Remove the luggage electrical key switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (UL) - 6 (E)
    No switch pushed
    10 kΩ or higher
    5 (UL) - 6 (E)
    Unlock switch pushed
    Below 1 Ω



NG
REPLACE LUGGAGE ELECTRICAL KEY SWITCH (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (LUGGAGE ELECTRICAL KEY SWITCH - CERTIFICATION ECU)
  1. Disconnect the X6 switch connector.

  1. Disconnect the G38 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    X6-5 (UL) - G38-22 (TSW5)
    Always
    Below 1 Ω
    G38-22 (TSW5) - Body ground
    Always
    10 kΩ or higher
    X6-6 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU


← Back Door Entry Unlock Function does not Operate (Aug 2013 – Jul 2014)Back Door Entry Lock and Unlock Functions do not Operate (Aug 2013 – Jul 2014) →