C1812/12 Pressure Sensor Malfunction / Upside
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
In the KDSS hydraulic circuit, the fluid is contained under pressure. If the fluid temperature is 20°C (68°F), the pressure is approximately 3.0 MPa (30.6 kgf/cm2, 435 psi).| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1812/12 |
One of the following conditions continues is met:
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER (OIL PRESSURE SENSOR) |
- NOTICE:
- Perform the inspection on a level surface.
- Perform the inspection with the vehicle empty.
- Make sure that the wheels are on the ground and facing straight ahead.
- Perform the inspection with the vehicle load completely on the suspension.
- Perform the inspection on a level surface.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / KDSS / Data List.
Select the item below in the Data List, and read the value displayed on the intelligent tester.
KDSS Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Oil Pressure Sensor
Oil pressure sensor/
Min.: -784.79 MPa (-8002.66 kgf/cm2, -113794.55 psi)
Max.: 784.76 MPa (8002.35 kgf/cm2, 113790.20 psi)
2.6 MPa (26.5 kgf/cm2, 377 psi) to 3.0 MPa (30.6 kgf/cm2, 435 psi): When vehicle stopped and fluid temperature 20°C (68°F)
-
Check the fluid pressure.
- OK:
- 2.6 MPa (26.5 kgf/cm2, 377 psi) to 3.0 MPa (30.6 kgf/cm2, 435 psi)
|
|
||||
| OK | |
| 2. RECONFIRM DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
DTC is output
A
DTC is not output
B
|
|
||||
| A | ||
| ||
| 3. INSPECT STABILIZER CONTROL ECU (SBP1 VOLTAGE) |
Connect the stabilizer control ECU connector.
Disconnect the Stabilizer control with accumulator housing connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
R20-3 (SBP1) - Body ground
Ignition switch ON
4.75 to 5.25 V
Text in Illustration *a
Front view of wire harness connector
(to Stabilizer Control with Accumulator Housing Assembly)
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (STABILIZER CONTROL ECU - ACCUMULATOR PRESSURE SENSOR) |
Disconnect the Stabilizer control ECU connector.
Disconnect the Stabilizer control with accumulator housing connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G123-17 (SOP1) - R20-2 (SOP1)
Always
Below 1 Ω
G123-17 (SOP1) - Body ground
Always
10 kΩ or higher
G123-6 (SGP1) - R20-1 (SGP1)
Always
Below 1 Ω
G123-6 (SGP1) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. INSPECT ACCUMULATOR PRESSURE SENSOR (OUTPUT VOLTAGE) |
Connect the stabilizer control ECU connector.
Connect the Stabilizer control with accumulator housing connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G123-17 (SOP1) - Body ground
Ignition switch ON
0.4 to 4.6 V
Text in Illustration *a
Component with harness connected
(Stabilizer Control ECU)
|
|
||||
| OK | ||
| ||
| 6. READ VALUE USING INTELLIGENT TESTER (OIL PRESSURE SENSOR) |
Disconnect the Stabilizer control with accumulator housing connector.
Connect the stabilizer control ECU connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / KDSS / Data List.
Select the item below in the Data List, and read the value displayed on the intelligent tester.
KDSS Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Oil Pressure Sensor
Oil pressure sensor/
Min.: -784.79 MPa (-8002.66 kgf/cm2, -113794.55 psi)
Max.: 784.76 MPa (8002.35 kgf/cm2, 113790.20 psi)
2.6 MPa (26.5 kgf/cm2, 377 psi) to 3.0 MPa (30.6 kgf/cm2, 435 psi): When vehicle stopped and fluid temperature 20°C (68°F)
-
Using a 1.5 V dry cell battery, connect the positive (+) lead to terminal 2 (SOP1) of the stabilizer control with accumulator housing connector and the negative (-) lead to terminal 1 (SGP1), and check that the Data List display changes.

- OK:
- Data List display changes.
Text in Illustration *a
Front view of wire harness connector
(to Stabilizer Control with Accumulator Housing Assembly)
|
|
||||
| OK | ||
| ||
| 7. CHECK HARNESS AND CONNECTOR (STABILIZER CONTROL ECU - ACCUMULATOR PRESSURE SENSOR) |
Disconnect the Stabilizer control ECU connector.
Disconnect the Stabilizer control with accumulator housing connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G123-15 (SBP1) - R20-3 (SBP1)
Always
Below 1 Ω
G123-15 (SBP1) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
