2013-2015 Land Cruiser Prado · Service Manual Suspension

INSTALLATION

Removal / installation · Vehicles built from Aug 2013


1. TEMPORARILY INSTALL FRONT STABILIZER LINK ASSEMBLY RH

  1. C214458E01
    Temporarily install the front stabilizer link assembly and spacer with the bolt.

    HINT:
    Make sure that the identification mark on the front stabilizer link assembly faces inward and toward the front of the vehicle.

    Text in Illustration 
    *a
    Mark Position


2. TEMPORARILY INSTALL FRONT STABILIZER WITH TUBE CYLINDER ASSEMBLY
  1. Install the 2 bleeder plug caps to the front stabilizer with tube cylinder assembly.

  1. C214456
    Temporarily install the front stabilizer with tube cylinder assembly with the nut and bolt.

    HINT:
    Pass the tube side of the front stabilizer with tube cylinder assembly under the return tube sub-assembly before installing it.

    NOTICE:
    1. Turn the bolt while holding the nut.
    2. Do not hold the front stabilizer with tube cylinder assembly by the cylinder boot.


3. CONNECT NO. 1 FRONT STABILIZER CONTROL TUBE ASSEMBLY
  1. Apply suspension fluid to the threads of the flare nuts.

  1. Using a union nut wrench, connect the No. 1 front stabilizer control tube to the front stabilizer with tube cylinder assembly and tighten the flare nuts.

    Torque:
    44 N*m{ 450 kgf*cm , 33 ft.*lbf }

    HINT:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Tighten the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


4. INSTALL FRAME APRON SEAL BRACKET
  1. Install the bracket with the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


5. INSTALL FRONT STABILIZER BAR

  1. C214685E01
    Install the 2 front stabilizer lower bracket bushes to the front stabilizer bar.

    HINT:
    Align the protrusions on the bushes with the identification marks on the front stabilizer bar with the protrusions facing inward.

    Text in Illustration 
    *a
    Protrusion
    *b
    Mark Position

  1. C214684
    With the identification marks of the front stabilizer bar facing downwards, support the front stabilizer bar with a jack.

    NOTICE:
    Place a wooden block between the jack and front stabilizer bar to prevent damage.

    HINT:
    Place the jack under the center of the vehicle.

  1. C214687E01
    Install the front stabilizer bar and 2 front stabilizer lower brackets with the 4 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    HINT:
    Make sure that the protrusions on the front stabilizer lower bracket bushes are positioned within 180° of the stabilizer cylinder and stabilizer link.

    Text in Illustration 
    *1
    Stabilizer Link
    *2
    Stabilizer Cylinder


6. INSTALL FRONT STABILIZER END BRACKET

  1. C214688E01
    Install the 2 front stabilizer brackets and 2 front stabilizer link bushes with the 4 bolts.

    Torque:
    75 N*m{ 765 kgf*cm , 55 ft.*lbf }

    HINT:
    There are stamps on the front stabilizer brackets to distinguish between the right and left brackets.


7. INSTALL FRONT SUSPENSION MEMBER BRACE SUB-ASSEMBLY
  1. Install the 2 member braces with the 6 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }


8. BLEED SUSPENSION FLUID
  1. Bleed the suspension fluid (Click here).


9. INSTALL FRONT WHEEL

Torque:
112 N*m{ 1142 kgf*cm , 83 ft.*lbf }


10. TIGHTEN FRONT STABILIZER LINK ASSEMBLY RH

  1. C214457
    Tighten the bolt on the front stabilizer link assembly.

    Torque:
    140 N*m{ 1428 kgf*cm , 103 ft.*lbf }

    NOTICE:
    Tighten the bolt with the wheels on the ground.


11. TIGHTEN FRONT STABILIZER WITH TUBE CYLINDER ASSEMBLY

  1. C214456
    Tighten the bolt on the front stabilizer with tube cylinder assembly.

    Torque:
    130 N*m{ 1326 kgf*cm , 96 ft.*lbf }

    NOTICE:
    Tighten the bolt with the wheels on the ground.


12. INSTALL FRONT FENDER APRON SEAL LH
  1. Install the front fender apron seal LH with the 7 clips.


13. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A224743
    Hook the engine under cover to the vehicle body as shown in the illustration.

  1. Install the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


14. INSTALL LOWER FRONT BUMPER COVER
  1. Install the front bumper cover lower with the 5 bolts and clip.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


15. INSTALL STABILIZER CONTROL VALVE PROTECTOR
  1. Install the stabilizer control valve protector with the 2 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


16. INSTALL SIDE STEP ASSEMBLY LH (for 5 Door)
  1. Install the side step with the 6 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. w/ Illumination:
    Connect the 2 connectors.


17. INSPECT VEHICLE HEIGHT
  1. Inspect the vehicle height (Click here).

← REMOVAL (from Aug 2013)COMPONENTS (from Aug 2013) →