2013-2015 Land Cruiser Prado · Service Manual Suspension

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT WHEEL LH

3. REMOVE REAR WHEEL LH

4. REMOVE SPARE TIRE

5. REMOVE SIDE STEP ASSEMBLY LH
  1. w/ Illumination:
    Disconnect the 2 connectors.

  1. Remove the 6 bolts and side step.

    B236304


6. REMOVE FRONT BUMPER COVER LOWER
  1. Remove the clip, 5 bolts and front bumper cover lower.


7. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts.

  1. A224743
    Unhook the engine under cover from the vehicle body as shown in the illustration.


8. REMOVE TRANSMISSION UNDER COVER
  1. Remove the 2 bolts and transmission under cover.


9. REMOVE STABILIZER CONTROL VALVE PROTECTOR

  1. C212853
    Remove the 2 bolts and stabilizer control valve protector.


10. DRAIN SUSPENSION FLUID

  1. C212854
    Loosen the bleeder plug on the stabilizer control with accumulator housing assembly and drain suspension fluid.

    HINT:
    1. Drain suspension fluid when performing operations related to the hydraulic circuits.
    2. Draining suspension fluid decreases suspension fluid pressure.

  1. Tighten the bleeder plug.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }


11. REMOVE FRONT STABILIZER TUBE PROTECTOR

  1. C212855
    Remove the 2 bolts and front stabilizer tube protector.


12. REMOVE FRONT STABILIZER CONTROL TUBE INSULATOR

  1. Remove the 2 bolts and front stabilizer control tube insulator.

    C302042E01

    Text in Illustration 
    *A
    for 1GR-FE
    *B
    for 1KD-FTV

    NOTICE:
    When replacing the front No. 1 stabilizer control tube assembly, do not install the front stabilizer control tube insulator as it becomes unnecessary.


13. DISCONNECT FRONT NO. 1 STABILIZER CONTROL TUBE ASSEMBLY

  1. When disconnecting the front No. 1 stabilizer control tube assembly before replacement:

    C300779E01

    Text in Illustration 
    *1
    Stabilizer Control with Accumulator Housing Assembly
    *2
    Front Stabilizer with Tube Cylinder Assembly

    1. Using a union nut wrench, disconnect the 2 flare nuts from the stabilizer control with accumulator housing.

    2. Using a union nut wrench, disconnect the 2 flare nuts from the front stabilizer with tube cylinder assembly.

  1. When disconnecting the front No. 1 stabilizer control tube assembly after replacement:

    C301808E01

    Text in Illustration 
    *1
    Stabilizer Control with Accumulator Housing Assembly
    *2
    Front Stabilizer with Tube Cylinder Assembly

    1. Using a union nut wrench, disconnect the 2 flare nuts from the stabilizer control with accumulator housing.

    2. Using a union nut wrench, disconnect the 2 flare nuts from the front stabilizer with tube cylinder assembly.

    3. Using a union nut wrench, disconnect the 2 flare nuts.


14. REMOVE FRONT NO. 1 STABILIZER CONTROL TUBE ASSEMBLY

  1. When removing the front No. 1 stabilizer control tube assembly before replacement:

    C300798E01

    Text in Illustration 
    *1
    Stabilizer Control with Accumulator Housing Assembly
    *2
    Front Stabilizer with Tube Cylinder Assembly
    *a
    Cut position
    -
    -

    1. Using a hacksaw, cut the front No. 1 stabilizer control tube assembly at the position shown in the illustration.

      CAUTION:
      1. Do not cut your fingers, etc.
      2. Wear protective goggles.

      NOTICE:
      1. Wrap protective tape around the cut ends of the front No. 1 stabilizer control tube assembly.
      2. Use a piece of cloth to protect the body from becoming damaged.

    2. Remove the bolt and front No. 1 stabilizer control tube assembly (stabilizer control with accumulator housing assembly side).

    3. Remove the bolt and front No. 1 stabilizer control tube assembly (front stabilizer with tube cylinder assembly side).

      NOTICE:
      Make sure that the drive shaft boot is not damaged during removal.

  1. When removing the front No. 1 stabilizer control tube assembly after replacement:

    C301810E01

    Text in Illustration 
    *1
    Stabilizer Control with Accumulator Housing Assembly
    *2
    Front Stabilizer with Tube Cylinder Assembly

    1. Remove the bolt and front No. 1 stabilizer control tube assembly (stabilizer control with accumulator housing assembly side).

    2. Remove the bolt (labeled A) and clamp from the front No. 1 stabilizer control tube assembly.

      C301811E01

      Text in Illustration 
      *1
      Front Stabilizer with Tube Cylinder Assembly
      -
      -

    3. Remove the bolt (labeled B), and then disconnect the front No. 1 stabilizer control tube assembly (front stabilizer with tube cylinder assembly side).

    4. Remove the front No. 1 stabilizer control tube assembly (lower part) and front No. 1 stabilizer control tube assembly (upper part).

      C301889E03

      Text in Illustration 
      *1
      Front No. 1 Stabilizer Control Tube Assembly (Upper Part)
      *2
      Front No. 1 Stabilizer Control Tube Assembly (Lower Part)


15. REMOVE FUEL PUMP CONTROL ECU ASSEMBLY

  1. A220754E01
    Disconnect the 2 connectors.
    Text in Illustration 
    *A
    w/o Air Suspension
    *B
    w/ Air Suspension

  1. Remove the 2 bolts and fuel pump ECU.

    NOTICE:
    Make sure the fuel pump ECU is not subjected to physical shocks, such as being dropped, etc.


16. REMOVE REAR SHOCK ABSORBER ASSEMBLY LH
(Click here)

17. DISCONNECT REAR NO. 1 STABILIZER CONTROL TUBE ASSEMBLY

  1. When disconnecting the rear No. 1 stabilizer control tube assembly before replacement:

    1. C301670
      Using a union nut wrench, disconnect the 2 flare nuts from the stabilizer control with accumulator housing.

    2. C301139
      Remove the 2 union bolts of the rear stabilizer control cylinder and the 2 pressure port gaskets.

  1. When disconnecting the rear No. 1 stabilizer control tube assembly after replacement:

    C301137

    1. Using a union nut wrench, disconnect the 2 flare nuts from the stabilizer control with accumulator housing.

    2. Using a union nut wrench, disconnect the 2 flare nuts.

    3. C301139
      Remove the 2 union bolts of the rear stabilizer control cylinder and the 2 pressure port gaskets.


18. REMOVE REAR NO. 1 STABILIZER CONTROL TUBE ASSEMBLY

  1. When removing the rear No. 1 stabilizer control tube assembly before replacement:

    C300799E01

    Text in Illustration 
    *1
    Stabilizer Control with Accumulator Housing Assembly
    *2
    Rear Stabilizer Control Cylinder
    *a
    Cut position
    -
    -

    1. Remove the 5 bolts and disconnect the rear No. 1 stabilizer control tube assembly.

    2. Using a hacksaw, cut the rear No. 1 stabilizer control tube assembly at the position shown in the illustration.

      CAUTION:
      1. Do not cut your fingers, etc.
      2. Wear protective goggles.

      NOTICE:
      1. Cut the rear No. 1 stabilizer control tube assembly while securely holding down the cut position.
      2. Use a piece of cloth to protect the body from becoming damaged.
      3. Wrap protective tape around the cut ends of the rear No. 1 stabilizer control tube assembly.

    3. Remove the cut rear No. 1 stabilizer control tube assembly (stabilizer control with accumulator housing assembly side).

    4. Using a plastic-faced hammer, lightly tap the cut rear No. 1 stabilizer control tube assembly (rear stabilizer control cylinder side) while sliding it to the right to remove it.

      C301655

      HINT:
      Performing this procedure with 2 persons may make the removal easier.

  1. When removing the rear No. 1 stabilizer control tube assembly after replacement:

    C301892E01

    Text in Illustration 
    *1
    Stabilizer Control with Accumulator Housing Assembly
    *2
    Rear Stabilizer Control Cylinder

    1. Remove the 2 bolts (labeled A) and disconnect the rear No. 1 stabilizer control tube assembly (stabilizer control with accumulator housing assembly side).

    2. Remove the 3 bolts (labeled B) and disconnect the rear No. 1 stabilizer control tube assembly (rear stabilizer control cylinder side).

    3. Using a plastic-faced hammer, lightly tap the rear No. 1 stabilizer control tube assembly (rear stabilizer control cylinder side) while sliding it to the right to remove it.

      C301815E01

      NOTICE:
      Make sure that the rear No. 1 stabilizer control tube assembly is not deformed, as the gaps shown by arrows A and B in the illustration are small.

      HINT:
      Performing this procedure with 2 persons may make the removal easier.

← COMPONENTS (from Aug 2013)REMOVAL (from Aug 2014) →