2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

Open in CAN Main Wire

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

There may be an open circuit in the CAN main wire and/or DLC3 CAN branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
  1. CAN main wire and connector
  2. ECM*1
  3. Combination meter assembly
  4. No. 1 junction connector
  5. No. 2 junction connector
  6. No. 3 junction connector
  7. No. 4 junction connector*2
  8. DLC3 CAN branch wire or connector
  1. *1: for 1KD-FTV
  2. *2: for 5L-E

WIRING DIAGRAM

C289506E02

INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - DLC3)

  1. C288300E11
    Disconnect the G132 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-4 (CANH) - G48-6 (CANH)
    Ignition switch off
    Below 1 Ω
    G132-15 (CANL) - G48-14 (CANL)
    Ignition switch off
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - ECM OR NO. 4 JUNCTION CONNECTOR)

  1. C242748E64
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-1 (CANH) - G132-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 5
OK


4. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

  1. C242748E65
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-8 (CANH) - G132-19 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 12
OK

REPLACE NO. 2 JUNCTION CONNECTOR

5. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


6. CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - ECM OR NO. 4 JUNCTION CONNECTOR)

  1. C242748E66
    Disconnect the G134 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-2 (CANH) - G134-13 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1KD-FTV)
    B
    NG (for 5L-E)
    C



B
Go to step 8

C
Go to step 10
A


7. CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

  1. C242748E67
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-1 (CANH) - G134-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK

REPLACE NO. 3 JUNCTION CONNECTOR

8. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


9. CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 3 JUNCTION CONNECTOR)

  1. C289504E01
    Disconnect the G58 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G58-35 (CANH) - G58-36 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 3 JUNCTION CONNECTOR)
OK

REPLACE ECM (Click here)

10. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


11. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

  1. C210060E64
    Disconnect the G101 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G101-3 (CANP) - G101-2 (CANN)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
OK

REPLACE NO. 4 JUNCTION CONNECTOR

12. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


13. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

  1. C242748E68
    Disconnect the A72 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-10 (CANH) - A72-21 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 15
OK


14. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

  1. C242748E69
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-9 (CANH) - A72-20 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK

REPLACE NO. 1 JUNCTION CONNECTOR

15. CONNECT CONNECTOR
  1. Reconnect the A72 No. 1 junction connector.


NEXT


16. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY - NO. 1 JUNCTION CONNECTOR)

  1. C198950E20
    Disconnect the G6 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G6-40 (CANH) - G6-39 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (COMBINATION METER ASSEMBLY - NO. 1 JUNCTION CONNECTOR)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)


← Audio Receiver Assembly Communication Stop Mode (from Aug 2014)Open in CAN Main Wire (from Aug 2014) →