TERMINALS OF ECU
System information · Vehicles built from Aug 2013
| CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY |


Disconnect the G24 and G25 amplifier connectors.
Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
G25-21 (B) - G25-14 (GND)
V - W-B
Battery power source
Always
11 to 14 V
G25-1 (IG+) - G25-14 (GND)
L - W-B
Ignition power supply
Ignition switch ON
11 to 14 V
Ignition switch off
Below 1 V
G25-14 (GND) - Body ground
W-B - Body ground
Ground for main power supply
Always
Below 1 Ω
G24-20 (RGND) - Body ground*1
W-B - Body ground
Ground for main power supply
Always
Below 1 Ω
G24-24 (+B2) - G24-20 (RGND)*1
GR - W-B
Battery power source
Always
11 to 14 V
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the G24 and G25 amplifier connectors.
Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
G25-3 (PTC1) - Body ground*2
V - Body ground
PTC NO. 1 relay operation signal
- Engine running (1250 rpm or more)
- Temperature setting MAX HOT
- Outside temperature 10°C (50°F) or less
- Engine coolant temperature 79°C (175°F) or less
- Headlight dimmer switch off
- Blower switch on
11 to 14 V*10
G25-4 (PTC3) - Body ground*2
P - Body ground
PTC NO. 3 relay operation signal
- Engine running (1250 rpm or more)
- Temperature setting MAX HOT
- Outside temperature 10°C (50°F) or less
- Engine coolant temperature 73°C (163°F) or less
- Headlight dimmer switch off
- Blower switch on
11 to 14 V*10
G25-5 (TAM) - G25-13 (SG-2)
V - G
Cooler thermistor (ambient temperature sensor) signal
- Ignition switch ON
- Ambient temperature 25°C (77°F)
1.35 to 1.75 V
G25-5 (TAM) - G25-13 (SG-2)
V - G
Cooler thermistor (ambient temperature sensor) signal
- Ignition switch ON
- Ambient temperature 40°C (104°F)
0.9 to 1.2 V
G25-8 (LOCK) - G25-13 (SG-2)
R - G
A/C compressor lock sensor signal
- Engine running
- Blower switch LO
- A/C switch on
Pulse generation
(See waveform 1)
G25-9 (PRE) - G25-13 (SG-2)*3
G - G
Air conditioner pressure sensor signal
- Ignition switch ON
- Refrigerant pressure normal (below 3.025 MPa [30.9 kgf/cm2, 438.6 psi] and higher than 0.176 MPa [1.8 kgf/cm2, 25.5 psi])
0.63 to 4.72 V
G25-9 (PRE) - G25-13 (SG-2)*3
G - G
Air conditioner pressure sensor signal
- Ignition switch ON
- Refrigerant pressure abnormal (below 0.176 MPa [1.8 kgf/cm2, 25.5 psi])
Below 0.63 V
G25-9 (PRE) - G25-13 (SG-2)*3
G - G
Air conditioner pressure sensor signal
- Ignition switch ON
- Refrigerant pressure abnormal (higher than 3.025 MPa [30.9 kgf/cm2, 438.6 psi])
4.72 V or higher
G25-9 (PRE) - Body ground*4
G - Body ground
No. 1 pressure switch signal
- Ignition switch ON
- Refrigerant pressure normal (below 3.14 MPa [32.0 kgf/cm2, 455 psi] and higher than 0.196 MPa [2.0 kgf/cm2, 28 psi])
Below 1 V
G25-9 (PRE) - Body ground*4
G - Body ground
No. 1 pressure switch signal
- Ignition switch ON
- Refrigerant pressure abnormal (below 0.196 MPa [2.0 kgf/cm2, 28 psi] or higher than 3.14 MPa [32.0 kgf/cm2, 455 psi])
4.69 V or higher
G25-10 (S5-3) - G25-13 (SG-2)
B - G
Power supply for air conditioner pressure sensor
Ignition switch ON
4.75 to 5.25 V
G25-15 (COOL) - G25-14 (GND)*5
V - W-B
Cooling box assembly operation signal
- Engine running
- Cooler control switch sub-assembly on
Below 1 V
G25-16 (MG+) - G25-14 (GND)*6
V - W-B
Viscous with magnetic clutch heater assembly operation signal
- Engine running
- Power heater switch on
Below 1 V
G25-17 (AC1) - G25-14 (GND)
LG - W-B
Compressor operation signal
- Ignition switch ON
- A/C switch on
Below 1 V
G25-18 (MHTR) - G25-14 (GND)
G - W-B
MIR HTR relay signal
- Ignition switch ON
- Mirror heater switch on
Below 1 V
G25-20 (MGC) - G25-14 (GND)
R - W-B
Magnet clutch assembly operation signal
- Ignition switch ON
- Blower switch LO
- A/C switch on
Below 1 V
G25-22 (PTC2) - Body ground*2
LG - Body ground
PTC NO. 2 relay operation signal
- Engine running (1250 rpm or more)
- Temperature setting MAX HOT
- Outside temperature 10°C (50°F) or less
- Engine coolant temperature 76°C (169°F) or less
- Headlight dimmer switch off
- Blower switch on
11 to 14 V*10
G25-23 (BLW) - G25-14 (GND)
L - W-B
Blower with fan motor sub-assembly control signal
- Ignition switch ON
- Blower switch LO
Pulse generation
(See waveform 2)
G25-25 (ALT) - G25-14 (GND)*2
L - W-B
Generator signal (PTC heater control)
Engine started
Pulse generation
G25-27 (ACT) - G25-14 (GND)
R - W-B
Compressor operation signal
- Ignition switch ON
- A/C switch on
4.75 to 5.25 V
G25-29 (TR) - G25-34 (SG-1)
GR - P
Cooler thermistor (room temperature sensor) signal
- Ignition switch ON
- Cabin temperature at 25°C (77°F)
1.8 to 2.2 V
- Ignition switch ON
- Cabin temperature at 40°C (104°F)
1.2 to 1.6 V
G25-32 (TSP) - G25-14 (GND)
V - W-B*8
G - W-B*9
Automatic light control sensor (solar sensor) power signal (for front passenger side)
- Ignition switch ON
- Solar sensor subjected to electric light
- Vehicle indoors
0.8 to 4.3 V
- Ignition switch ON
- Automatic light control sensor (solar sensor) covered with cloth
- Vehicle indoors
Below 0.8 V
G25-33 (TSD) - G25-14 (GND)
G - W-B*8
V - W-B*9
Automatic light control sensor (solar sensor) power signal (for driver side)
- Ignition switch ON
- Solar sensor subjected to electric light
- Vehicle indoors
0.8 to 4.3 V
- Ignition switch ON
- Automatic light control sensor (solar sensor) covered with cloth
- Vehicle indoors
Below 0.8 V
G25-36 (SWVC) - G25-14 (GND)*6, *7
W - W-B
- Heater switch assembly operation signal*6
- Idle up switch operation signal*7
- Ignition switch ON
- A/C switch on
- Heater switch assembly on*5
- Idle up switch on*6
Below 1 V
G24-1 (RBUS) - G24-21 (RBUG)*1
LG - L
BUS IC control signal (for Rear)
Ignition switch ON
Pulse generation
G24-4 (TEC) - G24-19 (SGND)*1
SB - V
Rear evaporator temperature sensor signal
- Ignition switch ON
- Rear evaporator temperature 0°C (32°F)
2.0 to 2.4 V
- Ignition switch ON
- Rear evaporator temperature 15°C (59°F)
1.4 to 1.8 V
G24-7 (SG-6) - Body ground*1
R - Body ground
Ground for cooler thermistor (rear room temperature sensor)
Always
Below 1 V
G24-12 (SWCB) - G25-14 (GND)*5
LG - W-B
Cooling box assembly operation signal
- Ignition switch ON
- A/C switch on
- Cooler control switch sub-assembly on
Below 1 V
G24-17 (TR) - G24-7 (SG-6)*1
B - R
Cooler thermistor (rear room temperature sensor) signal
- Ignition switch ON
- Cabin temperature 25°C (77°F)
1.8 to 2.2 V
- Ignition switch ON
- Cabin temperature 40°C (104°F)
1.2 to 1.6 V
G24-19 (SGND) - Body ground*1
V - Body ground
Ground for rear evaporator temperature sensor
Always
Below 1 V
G24-20 (RGND) - Body ground*1
W-B - Body ground
Ground for power supply
Always
Below 1 V
G24-22 (BLWH) - G24-20 (RGND)*1
W - W-B
Rear blower with fan motor sub-assembly control signal
- Ignition switch ON
- Rear blower switch on
Pulse generation
(See waveform 2)
G24-23 (RBBU) - G24-21 (RBUG)*1
P - L
Power supply for BUS IC (for Rear)
Always
11 to 14 V
z1-2 (BUS G) - Body ground
-
Ground for BUS IC
Always
Below 1 V
z1-3 (BUS) - z1-2 (BUS G)
-
BUS IC control signal
Ignition switch ON
Pulse generation
z1-4 (B BUS) - z1-2 (BUS G)
-
Power supply for BUS IC
Always
11 to 14 V
z1-6 (TEA) - z1-5 (SGA)
-
No. 1 cooler thermistor signal
- Ignition switch ON
- Evaporator temperature 0°C (32°F)
1.7 to 2.1 V
- Ignition switch ON
- Evaporator temperature 15°C (59°F)
0.9 to 1.3 V
- *1: w/ Rear Air Conditioning System
- *2: w/ PTC Heater
- *3: for 1KD-FTV or w/ Rear Air Conditioning System
- *4: except 1KD-FTV and w/o Rear Air Conditioning System
- *5: w/ Refrigerated Cool Box
- *6: w/ Viscous Heater
- *7: w/ Idle Up Switch
- *8: for LHD
- *9: for RHD
- HINT:
- *10: After the measurement conditions are met, wait 30 seconds before performing measurements.
- If the result is not as specified, the air conditioning amplifier assembly may have a malfunction.
- Engine running (1250 rpm or more)
Using an oscilloscope, check waveform 1.

A/C Compressor Lock Sensor Signal Item
Content
Terminal No. (Symbol)
G25-8 (LOCK) - G25-13 (SG-2)
Tool Setting
200 mV/DIV., 10 ms./DIV.
Condition
- Engine running
- A/C switch on
- Blower switch LO
- Engine running
Using an oscilloscope, check waveform 2.

Blower Motor Control Signal Item
Content
Terminal No. (Symbol)
- G25-23 (BLW) - G25-14 (GND)
- G24-22 (BLWH) - G24-20 (RGND)
Tool Setting
1 V/DIV., 500 μs/DIV.
Condition
- Ignition switch ON
- Blower switch LO
- HINT:
- When the blower level is increased, the duty ratio changes accordingly.
- G25-23 (BLW) - G25-14 (GND)
| CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (FOR COOLING BOX) (w/ Refrigerated Cool Box) |


Disconnect the air conditioning amplifier (for cooling box) connector.
Measure the resistance and voltage according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
1 (+B) - 4 (GND)
W-R - W-B
Battery power source
Always
11 to 14 V
2 (IG+) - 4 (GND)
GR - W-B
IG power supply
Ignition switch ON
11 to 14 V
Reconnect the air conditioning amplifier (for cooling box) connector.
Measure the resistance and voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
5 (SW) - 4 (GND)
LG-R - W-B
Cooler control switch sub-assembly operation signal
- Engine running
- Cooler control switch sub-assembly on
Below 1 V
6 (CBI) - 4 (GND)
L-G - W-B
Cooler compressor permission signal
- Engine running
- Cooler control switch sub-assembly on
Below 1 V
7 (LED) - 4 (GND)
L-B - W-B
Cooling box indicator signal
- Engine running
- Cooler control switch sub-assembly on
Below 1 V
8 (CBT) - 4 (GND)
BR-Y - W-B
Air conditioning amplifier assembly request signal
- Engine running
- Cooler control switch sub-assembly on
Below 1 V
9 (BLW) - 4 (GND)
W - W-B
No. 1 cooler blower motor sub-assembly operation signal
- Engine running
- Cooler control switch sub-assembly on
Below 1 V
10 (SG) - 4 (GND)
W-L - W-B
Ground
Always
Below 1 Ω
- Engine running
| CHECK INTEGRATION CONTROL AND PANEL ASSEMBLY |


Disconnect the G23 panel connector.
Measure the resistance and voltage according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
G23-1 (+B) - G23-4 (GND)
L - W-B
Battery power source
Always
11 to 14 V
G23-5 (IG) - G23-4 (GND)
L - W-B
IG power supply
Ignition switch ON
11 to 14 V
G23-6 (ACC) - G23-4 (GND)
P - W-B
ACC power supply
Ignition switch ACC
11 to 14 V
G23-4 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
| CHECK AIR CONDITIONING CONTROL ASSEMBLY (w/ Rear Air Conditioning System) |


Disconnect the T3 control connector.
Measure the resistance and voltage according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
T3-5 (IG) - T3-8 (E)
L - W-B
IG power supply
Ignition switch ON
11 to 14 V
T3-8 (E) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
| CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |


Remove the main body ECU (Click here).
Measure the voltage and resistance according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction in the wire harness.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A-11 (GND1) - Body ground
-
Ground
Always
Below 1 Ω
A-29 (ACC) - Body ground
-
ACC power supply
Ignition switch ACC
11 to 14 V
A-31 (ALTB) - Body ground
-
Battery power supply
Always
11 to 14 V
A-32 (IG) - Body ground
-
Ignition switch power supply
Ignition switch ON
11 to 14 V
Install the main body ECU (Click here).
Measure the voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
G64-20 (CLTB) - Body ground
P - Body ground
Automatic light control sensor power supply output
Ignition switch off
Below 1 V
Ignition switch ON
11 to 14 V
G64-22 (CLTE) - Body ground
L - Body ground
Automatic light control sensor ground
Always
Below 1 Ω
- If the result is not as specified, the main body ECU or driver side junction block assembly may have a malfunction.
- If the result is not as specified, the main body ECU or driver side junction block assembly may have a malfunction.