2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B1441/41 Air Mix Damper Control Servo Motor Circuit (Passenger Side)

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The damper servo sub-assembly (front passenger side air mix damper servo) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air mix damper (for front passenger side) to any position. As a result, the air mix damper (for front passenger side) varies the mixture of hot air from the heater core and cold air from the evaporator so that the temperature of the air blowing toward the front passenger side is as requested.

HINT:
Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.

DTC Code
DTC Detection Condition
Trouble Area
B1441/41
The air mix damper position does not change when the air conditioning amplifier assembly operates the damper servo sub-assembly (front passenger side air mix damper servo).
  1. Damper servo sub-assembly (front passenger side air mix damper servo)
  2. Air conditioning harness assembly
  3. Air conditioning amplifier assembly

WIRING DIAGRAM

E180810E50

INSPECTION PROCEDURE


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1441/41 is not output
    A
    DTC B1441/41 is output
    B
    DTC B1441/41/ and B1497/97 are output
    C



B
Go to step 2

C
GO TO B1497/97 (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

2. READ VALUE USING INTELLIGENT TESTER (FRONT PASSENGER SIDE AIR MIX DAMPER SERVO)
  1. Use the Data List to check if the damper servo sub-assembly (front passenger side air mix damper servo) is functioning properly (Click here).

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Mix Servo Targ Pulse (P)
    Damper servo sub-assembly (front passenger side air mix damper servo) target pulse / Min.: 0, Max.: 255
    for LHD:
    1. 112 or 127 (pulse): MAX COOL
    2. 21 or 31 (pulse): MAX HOT
    for RHD:
    1. 107 (pulse): MAX COOL
    2. 26 (pulse): MAX HOT
    -
    Air Mix Servo Actual Pulse (P)
    Damper servo sub-assembly (front passenger side air mix damper servo) actual pulse / Min.: 0, Max.: 255
    for LHD:
    1. 112 or 127 (pulse): MAX COOL
    2. 21 or 31 (pulse): MAX HOT
    for RHD:
    1. 107 (pulse): MAX COOL
    2. 26 (pulse): MAX HOT
    -

    OK:
    The display is as specified in the normal condition column.

    Result 
    Result
    Proceed to
    OK (When troubleshooting according to the DTC)
    A
    OK (When troubleshooting according to Problem Symptoms Table
    B
    Both target pulse and actual pulse do not display
    C
    Target pulse displays normally, but actual pulse does not display
    D



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

D
Go to step 4
A


3. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1441 is not output.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)

4. CHECK DAMPER SERVO SUB-ASSEMBLY (FRONT PASSENGER SIDE AIR MIX DAMPER SERVO)
  1. Replace the damper servo sub-assembly (front passenger side air mix damper servo) (Click here).

    HINT:
    Since the damper servo sub-assembly (front passenger side air mix damper servo) cannot be inspected while it is removed from the vehicle, replace the damper servo sub-assembly (front passenger side air mix damper servo) with a new or normally functioning one.

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1441 is not output.



NG
Go to step 5
OK

END (DAMPER SERVO SUB-ASSEMBLY [FRONT PASSENGER SIDE AIR MIX DAMPER SERVO] IS FAULTY)

5. CHECK AIR CONDITIONING HARNESS ASSEMBLY
  1. Temporarily replace the air conditioning harness assembly with a new or normally functioning one (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1441 is not output.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

END (AIR CONDITIONING HARNESS ASSEMBLY IS FAULTY)


← B1423/23 Pressure Sensor Circuit (from Aug 2014)B1441/41 Air Mix Damper Control Servo Motor Circuit (Passenger Side) (from Aug 2014) →