B2799 Engine Immobiliser System Malfunction
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
This DTC is stored when one of the following occurs: 1) the ECM detects errors in its own communications with the ID code box (immobiliser code ECU); 2) the ECM detects errors in the communication lines; or 3) the ECU communication ID between the ID code box (immobiliser code ECU) and ECM is different and an engine start is attempted.Before troubleshooting for this DTC, make sure no certification ECU DTCs are output. If output, troubleshoot the certification ECU DTCs first.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2799 |
One of the following conditions is met:
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the ID code box (immobiliser code ECU) or ECM, refer to the Service Bulletin.
| 1. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 2. CHECK FOR DTC |
Check for DTCs (Click here).
- OK:
- DTC B2799 is not output.
|
|
||||
| OK | ||
| ||
| 3. REGISTER ECU COMMUNICATION ID |
Register the ECU communication ID (Refer to the Service Bulletin).
| NEXT | |
| 4. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 5. CHECK FOR DTC |
Check for DTCs (Click here).
- OK:
- DTC B2799 is not output.
|
|
||||
| OK | ||
| ||
| 6. CHECK CONNECTION OF CONNECTOR |
Turn the engine switch off.
Check that the connectors are properly connected to the ECM and ID code box (immobiliser code ECU).
- OK:
- Connectors are properly connected.
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (ID CODE BOX - ECM) |
Disconnect the G37 ID code box (immobiliser code ECU) connector.
Disconnect the G56*1 or G58*2 or G60*3 ECM connector.
- *1: for 1GR-FE
- *2: for 1KD-FTV
- *3: for 2TR-FE
- *1: for 1GR-FE
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for 1GR-FE Tester Connection
Condition
Specified Condition
G37-5 (EFII) - G56-20 (IMO)
Always
Below 1 Ω
G37-6 (EFIO) - G56-14 (IMI)
Always
Below 1 Ω
G37-5 (EFII) or G56-20 (IMO) - Body ground
Always
10 kΩ or higher
G37-6 (EFIO) or G56-14 (IMI) - Body ground
Always
10 kΩ or higher
for 1KD-FTV Tester Connection
Condition
Specified Condition
G37-5 (EFII) - G58-29 (IMO)
Always
Below 1 Ω
G37-6 (EFIO) - G58-28 (IMI)
Always
Below 1 Ω
G37-5 (EFII) or G58-29 (IMO) - Body ground
Always
10 kΩ or higher
G37-6 (EFIO) or G58-28 (IMI) - Body ground
Always
10 kΩ or higher
for 2TR-FE Tester Connection
Condition
Specified Condition
G37-5 (EFII) - G60-32 (IMO)
Always
Below 1 Ω
G37-6 (EFIO) - G60-31 (IMI)
Always
Below 1 Ω
G37-5 (EFII) or G60-32 (IMO) - Body ground
Always
10 kΩ or higher
G37-6 (EFIO) or G60-31 (IMI) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 8. REPLACE ECM |
Temporarily replace the ECM with a new one.
- for 1GR-FE (Click here)
- for 1KD-FTV (Click here)
- for 2TR-FE(Click here)
- for 1GR-FE (Click here)
| NEXT | |
| 9. REGISTER ECU COMMUNICATION ID |
Register the ECU communication ID (Refer to the Service Bulletin).
| NEXT | |
| 10. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 11. CHECK FOR DTC |
Check for DTCs (Click here).
- OK:
- DTC B2799 is not output.
|
|
||||
| OK | ||
| ||
