2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B2799 Engine Immobiliser System Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

This DTC is stored when one of the following occurs: 1) the ECM detects errors in its own communications with the ID code box (immobiliser code ECU); 2) the ECM detects errors in the communication lines; or 3) the ECU communication ID between the ID code box (immobiliser code ECU) and ECM is different and an engine start is attempted.
Before troubleshooting for this DTC, make sure no certification ECU DTCs are output. If output, troubleshoot the certification ECU DTCs first.
DTC Code
DTC Detection Condition
Trouble Area
B2799
One of the following conditions is met:
  1. An error in the communication between the ECM and ID code box (immobiliser code ECU).
  2. An error in the communication lines.
  3. The communication ID is different during communication with the ID code box (immobiliser code ECU).
  1. Harness or connector
  2. ECM
  3. ID code box (immobiliser code ECU)

WIRING DIAGRAM

B355319E01

INSPECTION PROCEDURE

NOTICE:
When replacing the ID code box (immobiliser code ECU) or ECM, refer to the Service Bulletin.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2799 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID (Refer to the Service Bulletin).


NEXT


4. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


5. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2799 is not output.



NG
Go to step 6
OK

END (ECU COMMUNICATION ID IS NOT REGISTERED CORRECTLY)

6. CHECK CONNECTION OF CONNECTOR
  1. Turn the engine switch off.

  1. Check that the connectors are properly connected to the ECM and ID code box (immobiliser code ECU).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTOR CORRECTLY
OK


7. CHECK HARNESS AND CONNECTOR (ID CODE BOX - ECM)
  1. Disconnect the G37 ID code box (immobiliser code ECU) connector.

  1. Disconnect the G56*1 or G58*2 or G60*3 ECM connector.

    1. *1: for 1GR-FE
    2. *2: for 1KD-FTV
    3. *3: for 2TR-FE

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE 
    Tester Connection
    Condition
    Specified Condition
    G37-5 (EFII) - G56-20 (IMO)
    Always
    Below 1 Ω
    G37-6 (EFIO) - G56-14 (IMI)
    Always
    Below 1 Ω
    G37-5 (EFII) or G56-20 (IMO) - Body ground
    Always
    10 kΩ or higher
    G37-6 (EFIO) or G56-14 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV 
    Tester Connection
    Condition
    Specified Condition
    G37-5 (EFII) - G58-29 (IMO)
    Always
    Below 1 Ω
    G37-6 (EFIO) - G58-28 (IMI)
    Always
    Below 1 Ω
    G37-5 (EFII) or G58-29 (IMO) - Body ground
    Always
    10 kΩ or higher
    G37-6 (EFIO) or G58-28 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 2TR-FE 
    Tester Connection
    Condition
    Specified Condition
    G37-5 (EFII) - G60-32 (IMO)
    Always
    Below 1 Ω
    G37-6 (EFIO) - G60-31 (IMI)
    Always
    Below 1 Ω
    G37-5 (EFII) or G60-32 (IMO) - Body ground
    Always
    10 kΩ or higher
    G37-6 (EFIO) or G60-31 (IMI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. REPLACE ECM
  1. Temporarily replace the ECM with a new one.

    1. for 1GR-FE (Click here)
    2. for 1KD-FTV (Click here)
    3. for 2TR-FE(Click here)


NEXT


9. REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID (Refer to the Service Bulletin).


NEXT


10. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


11. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2799 is not output.



NG
REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
OK

END (ECM IS DEFECTIVE)


← B2799 Engine Immobiliser System Malfunction (Aug 2013 – Jul 2014)B279A Theft Deterrent System Communication Line High Fixation (Aug 2013 – Jul 2014) →