2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

U1002 Lost Communication with Gateway Module (Sensor Bus)

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

  1. The driving support ECU assembly stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the parking assist bus.
  2. When the driving support ECU assembly receives a response signal from the ECUs connected to the parking assist bus, the driving support ECU assembly recognizes and memorizes that the ECU is connected to the parking assist bus. Based on this memorized data, the driving support ECU assembly monitors for malfunctions in the ECUs connected to the parking assist bus when communicating with those ECUs. If the driving support ECU assembly cannot receive response signals from the ECUs that have been memorized as those connected to the parking assist bus, the driving support ECU assembly determines that a malfunction exists.
  3. If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).
DTC Code
DTC Detection Condition
Trouble Area
U1002
Lost communication with the gateway module (parking assist bus).
  1. Parking assist bus circuit
  2. Driving support ECU assembly CAN main wire or connector
  3. Millimeter wave radar sensor assembly CAN main wire or connector
  4. Driving support ECU assembly
  5. Millimeter wave radar sensor assembly
  1. For vehicles with a pre-crash safety system.

WIRING DIAGRAM

C295836E01

INSPECTION PROCEDURE

HINT:
Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR CAN BUS WIRE (CAN MAIN WIRE FOR DISCONNECTION, BUS LINE FOR SHORT CIRCUIT)

  1. C221683E04
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    resistance: Malfunction
    G119-40 (CA1P) - G119-18 (CA1N)
    Engine switch off
    54 to 69 Ω
    Below 53 Ω: Short in line
    G119-40 (CA1P) - G119-18 (CA1N)
    Engine switch off
    54 to 69 Ω
    Higher than 70 Ω: Open in CAN main bus line
    G119-40 (CA1P) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    G119-18 (CA1N) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    G119-40 (CA1P) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    Below 200 Ω: Ground short
    G119-18 (CA1N) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    Below 200 Ω: Ground short

    Text in Illustration 
    *a
    Component with harness connected
    (Driving Support ECU Assembly)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    NG
    1. Open in CAN main wire
    A
    NG
    1. Short in line
    2. +B short
    3. Ground short
    B
    OK
    C



B
Go to step 6

C
Go to step 9
A


3. CHECK FOR OPEN IN CAN BUS MAIN WIRE (DRIVING SUPPORT ECU ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

  1. C217352E14
    Disconnect the G119 driving support ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G119-40 (CA1P) - G119-18 (CA1N)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Driving Support ECU Assembly)



NG
Go to step 4
OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY (Click here)

4. CONNECT CONNECTOR
  1. Reconnect the G119 driving support ECU assembly connector.


NEXT


5. CHECK FOR OPEN IN CAN BUS MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)

  1. C207410E06
    Disconnect the A15 millimeter wave radar sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A15-4 (CA1P) - A15-3 (CA1N)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Millimeter Wave Radar Sensor Assembly)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MILLIMETER WAVE RADAR SENSOR (MILLIMETER WAVE RADAR SENSOR - DRIVING SUPPORT ECU ASSEMBLY)
OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (Click here)

6. CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT ECU ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

  1. C217423E16
    Disconnect the G119 driving support ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G119-40 (CA1P) - G119-18 (CA1N)
    Engine switch off
    108 to 132 Ω
    G119-40 (CA1P) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G119-18 (CA1N) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G119-40 (CA1P) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G119-18 (CA1N) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Driving Support ECU Assembly)
    *b
    Front view of DLC3



NG
Go to step 7
OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY (Click here)

7. CONNECT CONNECTOR
  1. Reconnect the G119 driving support ECU assembly connector.


NEXT


8. CHECK FOR SHORT IN CAN BUS WIRES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)

  1. C221151E03
    Disconnect the A15 millimeter wave radar sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A15-4 (CA1P) - A15-3 (CA1N)
    Engine switch off
    108 to 132 Ω
    A15-4 (CA1P) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    A15-3 (CA1N) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    A15-4 (CA1P) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    A15-3 (CA1N) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Millimeter Wave Radar Sensor Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MILLIMETER WAVE RADAR SENSOR (MILLIMETER WAVE RADAR SENSOR - DRIVING SUPPORT ECU ASSEMBLY)
OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (Click here)

9. CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BATTERY AND BODY GROUND)

  1. C217352E03
    Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the G119 driving support ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G119-25 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G119-30 (B) - Body ground
    Engine switch on (IG)
    11 to 14 V

Text in Illustration 
*a
Rear view of wire harness connector
(to Driving Support ECU Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY (Click here)


← U1002 Lost Communication with Gateway Module (MS Bus) (from Aug 2014)U1002 Lost Communication with Gateway Module (Sensor Bus) (from Aug 2014) →