U1002 Lost Communication with Gateway Module (Sensor Bus)
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
- The driving support ECU assembly stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the parking assist bus.
- When the driving support ECU assembly receives a response signal from the ECUs connected to the parking assist bus, the driving support ECU assembly recognizes and memorizes that the ECU is connected to the parking assist bus. Based on this memorized data, the driving support ECU assembly monitors for malfunctions in the ECUs connected to the parking assist bus when communicating with those ECUs. If the driving support ECU assembly cannot receive response signals from the ECUs that have been memorized as those connected to the parking assist bus, the driving support ECU assembly determines that a malfunction exists.
- If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).
| DTC Code |
DTC Detection Condition |
Trouble Area |
| U1002 |
Lost communication with the gateway module (parking assist bus). |
|
- For vehicles with a pre-crash safety system.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.
- NOTICE:
- After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
- After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
| NEXT | |
| 2. CHECK FOR CAN BUS WIRE (CAN MAIN WIRE FOR DISCONNECTION, BUS LINE FOR SHORT CIRCUIT) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
resistance: Malfunction
G119-40 (CA1P) - G119-18 (CA1N)
Engine switch off
54 to 69 Ω
Below 53 Ω: Short in line
G119-40 (CA1P) - G119-18 (CA1N)
Engine switch off
54 to 69 Ω
Higher than 70 Ω: Open in CAN main bus line
G119-40 (CA1P) - G48-16 (BAT)
Engine switch off
6 kΩ or higher
Below 6 kΩ: +B short
G119-18 (CA1N) - G48-16 (BAT)
Engine switch off
6 kΩ or higher
Below 6 kΩ: +B short
G119-40 (CA1P) - G48-4 (CG)
Engine switch off
200 Ω or higher
Below 200 Ω: Ground short
G119-18 (CA1N) - G48-4 (CG)
Engine switch off
200 Ω or higher
Below 200 Ω: Ground short
Text in Illustration *a
Component with harness connected
(Driving Support ECU Assembly)
*b
Front view of DLC3
Result Result
Proceed to
NG - Open in CAN main wire
A
NG - Short in line
- +B short
- Ground short
B
OK
C
|
|
||||
|
|
||||
| A | |
| 3. CHECK FOR OPEN IN CAN BUS MAIN WIRE (DRIVING SUPPORT ECU ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY) |
Disconnect the G119 driving support ECU assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G119-40 (CA1P) - G119-18 (CA1N)
Engine switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to Driving Support ECU Assembly)
|
|
||||
| OK | ||
| ||
| 4. CONNECT CONNECTOR |
Reconnect the G119 driving support ECU assembly connector.
| NEXT | |
| 5. CHECK FOR OPEN IN CAN BUS MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY) |
Disconnect the A15 millimeter wave radar sensor assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
A15-4 (CA1P) - A15-3 (CA1N)
Engine switch off
108 to 132 Ω
Text in Illustration *a
Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
|
|
||||
| OK | ||
| ||
| 6. CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT ECU ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY) |
Disconnect the G119 driving support ECU assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G119-40 (CA1P) - G119-18 (CA1N)
Engine switch off
108 to 132 Ω
G119-40 (CA1P) - G48-4 (CG)
Engine switch off
200 Ω or higher
G119-18 (CA1N) - G48-4 (CG)
Engine switch off
200 Ω or higher
G119-40 (CA1P) - G48-16 (BAT)
Engine switch off
6 kΩ or higher
G119-18 (CA1N) - G48-16 (BAT)
Engine switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to Driving Support ECU Assembly)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 7. CONNECT CONNECTOR |
Reconnect the G119 driving support ECU assembly connector.
| NEXT | |
| 8. CHECK FOR SHORT IN CAN BUS WIRES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY) |
Disconnect the A15 millimeter wave radar sensor assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
A15-4 (CA1P) - A15-3 (CA1N)
Engine switch off
108 to 132 Ω
A15-4 (CA1P) - G48-4 (CG)
Engine switch off
200 Ω or higher
A15-3 (CA1N) - G48-4 (CG)
Engine switch off
200 Ω or higher
A15-4 (CA1P) - G48-16 (BAT)
Engine switch off
6 kΩ or higher
A15-3 (CA1N) - G48-16 (BAT)
Engine switch off
6 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 9. CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BATTERY AND BODY GROUND) |
Connect the cable to the negative (-) battery terminal.

- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
Disconnect the G119 driving support ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G119-25 (GND) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G119-30 (B) - Body ground
Engine switch on (IG)
11 to 14 V
| *a |
Rear view of wire harness connector (to Driving Support ECU Assembly) |
|
|
||||
| OK | ||
| ||
