U1002 Lost Communication with Gateway Module (MS Bus)
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
- The main body ECU (multiplex network body ECU) stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the CAN MS bus.
- When the main body ECU (multiplex network body ECU) receives a response signal from the ECUs connected to the CAN MS bus, the main body ECU (multiplex network body ECU) recognizes and memorizes that the ECU is connected to the CAN MS bus. Based on this memorized data, the main body ECU (multiplex network body ECU) monitors for malfunctions in the ECUs connected to the CAN MS bus when communicating with those ECUs. If the main body ECU (multiplex network body ECU) cannot receive response signals from the ECUs that have been memorized as those connected to the CAN MS bus, the main body ECU (multiplex network body ECU) determines that a malfunction exists.
- If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).
| DTC Code |
DTC Detection Condition |
Trouble Area |
| U1002 |
Lost communication with the gateway module. |
|
- For vehicles with a multi-function switch.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
| NEXT | |
| 2. CHECK CAN BUS WIRE (CHECK CAN MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
Resistance: Malfunction
G103-3 (CANP) - G103-2 (CANN)
Ignition switch off
54 to 69 Ω
Below 53 Ω: Short in line
G103-3 (CANP) - G103-2 (CANN)
Ignition switch off
54 to 69 Ω
Higher than 70 Ω: Open in CAN main bus line
G103-3 (CANP) - G48-16 (BAT)
Ignition switch off
6 kΩ or higher
Below 6 kΩ: +B short
G103-2 (CANN) - G48-16 (BAT)
Ignition switch off
6 kΩ or higher
Below 6 kΩ: +B short
G103-3 (CANP) - G48-4 (CG)
Ignition switch off
200 Ω or higher
Below 200 Ω: Ground short
G103-2 (CANN) - G48-4 (CG)
Ignition switch off
200 Ω or higher
Below 200 Ω: Ground short
Text in Illustration *a
Component with harness connected
(No. 8 Junction Connector)
*b
Front view of DLC3
Result Result
Proceed to
NG - Open in CAN main bus line
A
NG - Short in line
- +B short
- GND short
B
OK
C
|
|
||||
|
|
||||
| A | |
| 3. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU) |
![]() ![]() |
Disconnect the G96 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G96-4 (CANH) - G96-15 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 3 Junction Connector)
|
|
||||
| OK | |
| 4. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 8 JUNCTION CONNECTOR) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G96-6 (CANH) - G96-17 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 3 Junction Connector)
|
|
||||
| OK | ||
| ||
| 5. CONNECT CONNECTOR |
Reconnect the G96 No. 3 junction connector.
| NEXT | |
| 6. CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU) |
Disconnect the G63 main body ECU (multiplex network body ECU) connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G63-9 (CANP) - G63-10 (CANN)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
|
|
||||
| OK | ||
| ||
| 7. CONNECT CONNECTOR |
Reconnect the G96 No. 3 junction connector.
| NEXT | |
| 8. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 JUNCTION CONNECTOR) |
Disconnect the G103 No. 8 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G103-3 (CANP) - G103-2 (CANN)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 8 Junction Connector)
|
|
||||
| OK | ||
| ||
| 9. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - DRIVING SUPPORT SWITCH CONTROL ECU) |
Disconnect the G96 No. 3 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G96-5 (CANH) - G96-16 (CANL)
Ignition switch off
200 Ω or higher
G96-5 (CANH) - G48-4 (CG)
Ignition switch off
200 Ω or higher
G96-16 (CANL) - G48-4 (CG)
Ignition switch off
200 Ω or higher
G96-5 (CANH) - G48-16 (BAT)
Ignition switch off
6 kΩ or higher
G96-16 (CANL) - G48-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 3 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 10. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G96-4 (CANH) - G96-15 (CANL)
Ignition switch off
108 to 132 Ω
G96-4 (CANH) - G48-4 (CG)
Ignition switch off
200 Ω or higher
G96-15 (CANL) - G48-4 (CG)
Ignition switch off
200 Ω or higher
G96-4 (CANH) - G48-16 (BAT)
Ignition switch off
6 kΩ or higher
G96-15 (CANL) - G48-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 3 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 11. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 8 JUNCTION CONNECTOR) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G96-6 (CANH) - G96-17 (CANL)
Ignition switch off
108 to 132 Ω
G96-6 (CANH) - G48-4 (CG)
Ignition switch off
200 Ω or higher
G96-17 (CANL) - G48-4 (CG)
Ignition switch off
200 Ω or higher
G96-6 (CANH) - G48-16 (BAT)
Ignition switch off
6 kΩ or higher
G96-17 (CANL) - G48-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 3 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 12. CONNECT CONNECTOR |
Reconnect the G96 No. 3 junction connector.
| NEXT | |
| 13. CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT SWITCH CONTROL ECU) |
for Automatic Transmission:
Disconnect the G163 driving support switch control ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G163-2 (CANP) - G163-3 (CANN)
Ignition switch off
54 to 69 Ω
G163-2 (CANP) - G48-4 (CG)
Ignition switch off
200 Ω or higher
G163-3 (CANN) - G48-4 (CG)
Ignition switch off
200 Ω or higher
G163-2 (CANP) - G48-16 (BAT)
Ignition switch off
6 kΩ or higher
G163-3 (CANN) - G48-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to Driving Support Switch Control ECU)
*b
Front view of DLC3
for Manual Transmission:
Disconnect the G76 driving support switch control ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G76-9 (CANP) - G76-10 (CANN)
Ignition switch off
54 to 69 Ω
G76-9 (CANP) - G48-4 (CG)
Ignition switch off
200 Ω or higher
G76-10 (CANN) - G48-4 (CG)
Ignition switch off
200 Ω or higher
G76-9 (CANP) - G48-16 (BAT)
Ignition switch off
6 kΩ or higher
G76-10 (CANN) - G48-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to Driving Support Switch Control ECU)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 14. CONNECT CONNECTOR |
Reconnect the G96 No. 3 junction connector.
| NEXT | |
| 15. CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU) |
Disconnect the G63 main body ECU (multiplex network body ECU) connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G63-9 (CANP) - G63-10 (CANN)
Ignition switch off
108 to 132 Ω
G63-9 (CANP) - G48-4 (CG)
Ignition switch off
200 Ω or higher
G63-10 (CANN) - G48-4 (CG)
Ignition switch off
200 Ω or higher
G63-9 (CANP) - G48-16 (BAT)
Ignition switch off
6 kΩ or higher
G63-10 (CANN) - G48-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 16. CONNECT CONNECTOR |
Reconnect the G96 No. 3 junction connector.
| NEXT | |
| 17. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR) |
Disconnect the G103 No. 8 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
G103-3 (CANP) - G103-2 (CANN)
Ignition switch off
108 to 132 Ω
G103-3 (CANP) - G48-4 (CG)
Ignition switch off
200 Ω or higher
G103-2 (CANN) - G48-4 (CG)
Ignition switch off
200 Ω or higher
G103-3 (CANP) - G48-16 (BAT)
Ignition switch off
6 kΩ or higher
G103-2 (CANN) - G48-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 8 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 18. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND) |
Connect the cable to the negative (-) battery terminal.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


Text in Illustration *a
Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b
Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
Remove the main body ECU (multiplex network body ECU) (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G63-3 (GND2) - Body ground
Always
Below 1 Ω
A-11 (GND1) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
A-31 (ALTB) - Body ground
Always
11 to 14 V
A-30 (BECU) - Body ground
Always
11 to 14 V
A-29 (ACC) - Body ground
Ignition switch ACC
11 to 14 V
A-32 (IG) - Body ground
Ignition switch ON
11 to 14 V
|
|
||||
| OK | ||
| ||

