2013-2015 Land Cruiser Prado · Service Manual Steering

Steering Wheel does not Heat Up When Heated Steering Wheel Switch is Pressed

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

(Click here)

WIRING DIAGRAM

C221421E04

INSPECTION PROCEDURE


1. CHECK STEERING HEATER SWITCH (LED OPERATION)
C221135
  1. Check the illumination condition of the LED.

    Result:
    LED
    Condition
    Proceed to
    Illuminates
    Engine switch on (IG)
    Heated steering wheel switch is pushed
    B
    Does not illuminate
    Engine switch on (IG)
    Heated steering wheel switch is pushed and held continuously for 10 seconds or more
    A



B
Go to step 3
A


2. INSPECT STEERING WHEEL ASSEMBLY (THERMISTOR)
  1. Disconnect the steering wheel controller connector.

  1. C234543E03
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (TH2) - 2 (TH1)
    10 to 30 °C(50 to 86°F)
    8.132 to 18.43 kΩ

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Heated Steering Wheel Controller)



NG
REPLACE STEERING WHEEL ASSEMBLY (Click here)
OK


3. INSPECT STEERING WHEEL ASSEMBLY (HEATER·THERMOSTAT)
  1. Disconnect the steering wheel controller connector.

  1. C234543E04
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (SH1) - 3 (SH2)
    20°C (68°F)
    1.89 to 2.25 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Heated Steering Wheel Controller)



NG
REPLACE STEERING WHEEL ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (STEERING HEATER SWITCH - SPIRAL CABLE)
  1. Disconnect the G152 steering heater switch connector.

  1. Disconnect the G151 spiral cable connector.

  1. C221428E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G152-5 (INDC) - G151-1 (BTM)
    Always
    Below 1 Ω
    G152-4 (RC) - G151-3 (ETM)
    Always
    Below 1 Ω
    G151-2 (EHT) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Heater Switch)
    *b
    Front view of wire harness connector
    (to Spiral Cable)

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G151-4 (BHT) - Body ground
    Engine switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE WIRE HARNESS OR CONNECTOR
OK


Go to step 6

5. INSPECT SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
If there are any defects as mentioned below, replace the spiral cable with a new one:
Scratches, cracks, dents or chips in the connector or spiral cable.

  1. Disconnect the G151 spiral cable connector.

  1. Disconnect the heated steering wheel controller connector.

  1. C149098E06
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (CCU) - G151-1 (BTM)
    Always
    Below 1 Ω
    2 (CCV) - G151-3 (ETM)
    Always
    Below 1 Ω
    3 (CCX) - G151-2 (EHT)
    Always
    Below 1 Ω
    4 (CCW) - G151-4 (BHT)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Spiral Cable)
    *b
    Front view of harness connector
    (to Heated Steering Wheel Controller)



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


6. CHECK STEERING HEATER SWITCH
  1. Disconnect the G152 steering heater switch connector.

  1. C221426E02
    Measure the voltage according to the value(s) in the table below.

    HINT:
    As the circuit has a diode, perform the measurement in diode test mode and make sure that the polarity is correct.

    Standard Voltage:
    Tester Connection
    Positive (+) tester probe - Negative (-) tester probe
    Switch Condition
    Specified Condition
    G152-1 (IG) - G152-4 (RC)
    Heated steering wheel switch is pushed
    Below 1.25 V

    Text in Illustration 
    *a
    Component without harness connected
    (to Steering Heater Switch)



NG
REPLACE STEERING HEATER SWITCH (Click here)
OK

REPLACE STEERING WHEEL HEATER CONTROL ASSEMBLY (Click here)


← Steering Wheel does not Heat Up When Heated Steering Wheel Switch is Pressed (Aug 2013 – Jul 2014)PRECAUTION (from Aug 2013) →