2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Diagnosis Circuit

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.
DTCs are output by the blinking of the SRS warning light.

HINT:
  1. When each warning light continues blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.
  2. A DTC output mode signal is transmitted through the CAN communication system to each ECU including the center airbag sensor. Thus, when all systems do not enter DTC output mode, there may be an ECM malfunction.


WIRING DIAGRAM

C217718E01

INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output.

    Result 
    Result
    Proceed to
    DTCs are output (for LHD with Entry and Start System)
    A
    DTCs are output (for LHD without Entry and Start System)
    B
    DTCs are output (for RHD with Entry and Start System)
    C
    DTCs are output (for RHD without Entry and Start System)
    D
    DTC is not output
    E



A
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (for LHD with Entry and Start System) (Click here)

B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (for LHD without Entry and Start System) (Click here)

C
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (for RHD with Entry and Start System) (Click here)

D
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (for RHD without Entry and Start System) (Click here)
E


2. CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
  1. *1: for 1GR-FE
  2. *2: for 2TR-FE

  1. C217199E02
    Turn the ignition switch off.

  1. Disconnect the G56*1, G60*2 connector from the ECM.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G48-13 (TC) - G56-28 (TC)*1
    Always
    Below 1 Ω
    G48-13 (TC) - G60-13 (TC)*2
    Always
    Below 1 Ω

    Text in Illustration 
    *A
    for 1GR-FE
    *B
    for 2TR-FE
    *a
    Front view of DLC3
    *b
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

  1. C198509E06
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G48-4 (CG) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of DLC3



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
  1. *1: for 1GR-FE
  2. *2: for 2TR-FE

  1. C217200E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G56-28 (TC)*1 - Body ground
    Always
    1 MΩ or higher
    G60-13 (TC)*2 - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *A
    for 1GR-FE
    *B
    for 2TR-FE
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)


← SRS Warning Light does not Come ON (from Aug 2014)Diagnosis Circuit (from Aug 2014) →