2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B1656/38 Seat Belt Buckle Switch LH Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The seat belt buckle switch LH circuit consists of the center airbag sensor and front seat inner belt LH.
DTC B1656/38 is stored when a malfunction is detected in the seat belt buckle switch LH circuit.
DTC Code
DTC Detection Condition
Trouble Area
B1656/38
One of the following conditions is met:
  1. The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the seat belt buckle switch LH circuit for 2 seconds.
  2. A front seat inner belt LH malfunction.
  3. A center airbag sensor malfunction.
  1. No. 2 floor wire
  2. Front seat inner belt assembly LH (Seat belt buckle switch LH)
  3. Center airbag sensor assembly

WIRING DIAGRAM

C213926E07

INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).


1. CHECK FOR DTC
  1. Turn the ignition switch to ON.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1656 is not output.

    HINT:
    Codes other than DTC B1656 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and front seat inner belt LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


3. CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and front seat inner belt LH.

  1. C215710E01
    Check that the connectors (on the center airbag sensor side and front seat inner belt LH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.

    Text in Illustration 
    *1
    Front Seat Inner Belt LH
    *2
    Center Airbag Sensor



NG
REPLACE NO. 2 FLOOR WIRE
OK


4. CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.C217040E10

    Text in Illustration 
    *1
    Front Seat Inner Belt LH
    *2
    Center Airbag Sensor
    *3
    No. 2 Floor Wire
    *4
    Connector C
    *5
    Connector B
    -
    -
    *a
    Front view of wire harness connector
    (to Front Seat Inner Belt LH)
    *b
    Rear view of wire harness connector
    (to Center Airbag Sensor)

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    R10-2 (LBE+) - Body ground
    Ignition switch ON
    Below 1 V
    R10-1 (LBE-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R10-2 (LBE+) - R1-11 (LBE+)
    Always
    Below 1 Ω
    R10-1 (LBE-) - R1-12 (LBE-)
    Always
    Below 1 Ω
    R10-2 (LBE+) - Body ground
    Always
    1 MΩ or higher
    R10-1 (LBE-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE NO. 2 FLOOR WIRE
OK


5. CHECK FRONT SEAT INNER BELT LH (SEAT BELT BUCKLE SWITCH)

  1. C157773E01
    Connect the connectors to the center airbag sensor and front seat inner belt LH.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1656 is not output.

    HINT:
    Codes other than DTC B1656 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Front Seat Inner Belt LH
    *2
    Center Airbag Sensor



NG
Go to step 6
OK

USE SIMULATION METHOD TO CHECK (Click here)

6. REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the front seat inner belt LH (Click here).

    HINT:
    Perform the inspection using parts from a normally functioning vehicle if possible.


NEXT


7. CHECK CENTER AIRBAG SENSOR

  1. C157773E01
    Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1656 is not output.

    HINT:
    Codes other than DTC B1656 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Front Seat Inner Belt LH
    *2
    Center Airbag Sensor



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)


← B1656/38 Seat Belt Buckle Switch LH Circuit Malfunction (Aug 2013 – Jul 2014)B1660/43 Passenger Airbag OFF Indicator Circuit Malfunction (Aug 2013 – Jul 2014) →