U1110 Lost Communication with Clearance Sonar Module
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
| DTC Code |
DTC Detection Condition |
Trouble Area |
| U1110 |
There is no communication from the clearance warning ECU assembly. |
|
- For vehicles with a TOYOTA parking assist-sensor system.
WIRING DIAGRAM




INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- HINT:
- Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.
- NOTICE:
- After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
- After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
| NEXT | |
| 2. CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY CAN BRANCH WIRE) |
Disconnect the I1*1 or G154*2 clearance warning ECU assembly connector.

- *1: for 4 Sensor Type
- *2: for 8 Sensor Type
- *1: for 4 Sensor Type
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for 4 Sensor Type Tester Connection
Switch Condition
Specified Condition
I1-3 (R1) - I1-5 (R2)
Engine switch off
54 to 69 Ω
for 8 Sensor Type Tester Connection
Switch Condition
Specified Condition
G154-3 (R1) - G154-5 (R2)
Engine switch off
54 to 69 Ω
Text in Illustration *A
for 4 Sensor Type
*B
for 8 Sensor Type
*a
Front view of wire harness connector
(to Clearance Warning ECU Assembly)
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BATTERY AND BODY GROUND) |
Connect the cable to the negative (-) battery terminal.

- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for 4 Sensor Type Tester Connection
Condition
Specified Condition
I1-17 (E) - Body ground
Always
Below 1 Ω
for 8 Sensor Type Tester Connection
Condition
Specified Condition
G154-17 (E) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
for 4 Sensor Type Tester Connection
Switch Condition
Specified Condition
I1-15 (IG) - Body ground
Engine switch on (IG)
11 to 14 V
for 8 Sensor Type Tester Connection
Switch Condition
Specified Condition
G154-15 (IG) - Body ground
Engine switch on (IG)
11 to 14 V
| *A |
for 4 Sensor Type |
| *B |
for 8 Sensor Type |
| *a |
Front view of wire harness connector (to Clearance Warning ECU Assembly) |
|
|
||||
| OK | ||
| ||
