2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

U1115 Lost Communication with Tilt and Telescopic Module

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

DTC Code
DTC Detection Condition
Trouble Area
U1115
There is no communication from the multiplex tilt and telescopic ECU.
  1. Power source or inside multiplex tilt and telescopic ECU
  2. Multiplex tilt and telescopic ECU CAN branch wire or connector
  3. Multiplex tilt and telescopic ECU
  1. For vehicles with power tilt and power telescopic steering column.

WIRING DIAGRAM

C184654E04

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAB main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR OPEN IN CAN BUS WIRE (MULTIPLEX TILT AND TELESCOPIC ECU CAN BRANCH WIRE)

  1. C101073E01
    Disconnect the G116 multiplex tilt and telescopic ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G116-5 (CANP) - G116-14 (CANN)
    Engine switch off
    54 to 64 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Multiplex Tilt and Telescopic ECU)



NG
REPAIR OR REPLACE MULTIPLEX TILT AND TELESCOPIC ECU CAN BRANCH WIRE OR CONNECTOR (CANP, CANN)
OK


3. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY AND BODY GROUND)

  1. C101073E02
    Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G116-11 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G116-2 (+B) - Body ground
    Always
    11 to 14 V
    G116-9 (ECUB) - Body ground
    Always
    11 to 14 V
    G116-8 (IG) - Body ground
    Engine switch on (IG)
    11 to 14 V

Text in Illustration 
*a
Rear view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)


← U1114 Lost Communication with Main Switch Module (from Aug 2014)U1115 Lost Communication with Tilt and Telescopic Module (from Aug 2014) →