2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. REMOVE JACK BOX HOLE COVER (for 3 Door)

B236402E01
  1. Using a screwdriver, detach the 2 claws and remove the jack box hole cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


2. REMOVE BACK DOOR CHECK (for 3 Door)

NOTICE:
  1. If the back door check is detached from a ball joint, do not reuse it as the connection with the ball joint will be loose, resulting in the back door check falling off.
  2. If the back door check is detached from a ball joint, it becomes non-reusable. Therefore, do not detach the back door check from a ball joint unless replacing it.

  1. B340680
    Remove the 2 bolts.

  1. Using a clip remover, detach the clip and remove the back door check with back door lower damper stay bracket.

  1. B246611
    Detach the wire harness clamp.

  1. Remove the 3 bolts and back door check with back door lower damper stay bracket.


3. REMOVE REAR BUMPER BAR PLATE (for 3 Door)
  1. Put protective tape around the rear bumper bar plate.

  1. Detach the 14 claws and remove the rear bumper bar plate.

    B236403E01

    Text in Illustration 
    *1
    Protective Tape
    -
    -


4. REMOVE REAR NO. 1 BUMPER PLATE (for 3 Door)
  1. Put protective tape around the No. 1 rear bumper plate.

  1. Detach the 10 claws and 10 guides and remove the No. 1 rear bumper plate.

    B236404E01

    Text in Illustration 
    *1
    Protective Tape
    -
    -


5. REMOVE REAR QUARTER PANEL MUDGUARD LH (for 3 Door)

B236299
  1. Remove the 2 clips and 5 screws.

  1. Remove the rear quarter panel mudguard.


6. REMOVE REAR QUARTER PANEL MUDGUARD RH (for 3 Door)

HINT:
Use the same procedure described for the LH side.


7. REMOVE REAR BUMPER COVER (for 3 Door)
  1. Put protective tape around the rear bumper cover.

  1. Remove the 2 clips and 7 bolts.

  1. Detach the 10 claws.

  1. w/ TOYOTA Parking Assist-sensor System, w/ Rear Fog Light:
    Disconnect the 4 connectors.

  1. w/ TOYOTA Parking Assist-sensor System, w/o Rear Fog Light:
    Disconnect the 2 connectors.

  1. w/o TOYOTA Parking Assist-sensor System, w/ Rear Fog Light:
    Disconnect the 2 connectors.

  1. Remove the rear bumper cover.

    B236407E01

    Text in Illustration 
    *1
    Protective Tape
    -
    -


8. REMOVE REAR BUMPER SIDE MOUNTING BRACKET LH (for 3 Door)

B239519
  1. w/ Entry and Start System:
    Disconnect the connector.

  1. Remove the bolt and rear bumper side moulding bracket.


9. REMOVE ELECTRICAL KEY ANTENNA (for 3 Door)

  1. B241231
    Remove the bolt and antenna.


10. REMOVE ELECTRICAL KEY ANTENNA (for 5 Door)

  1. B241233
    Disconnect the connector.

  1. Remove the bolt and antenna.

← COMPONENTS (from Aug 2013)REMOVAL (from Aug 2014) →