2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT BUMPER LOWER COVER
  1. Remove the clip, 5 bolts and front bumper lower cover.


3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts and No. 1 engine under cover.


4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. A218364
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug.

    A218365E01

    Text in Illustration 
    *1
    Radiator Reservoir
    *2
    Vent Plug
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug


5. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
  1. Remove the cowl top ventilator louver (Click here).


6. REMOVE DIESEL THROTTLE BODY ASSEMBLY
  1. Remove the diesel throttle body (Click here).


7. DISCONNECT NO. 3 WATER BY-PASS HOSE

  1. A223447
    Remove the clamp.

  1. Disconnect the No. 3 water by-pass hose from the EGR cooler.


8. DISCONNECT NO. 4 WATER BY-PASS HOSE
  1. Disconnect the No. 4 water by-pass hose from the EGR cooler.


9. REMOVE INJECTION PIPE

NOTICE:
  1. After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating the injector inlet.

  1. A223449
    Remove the 2 nuts and No. 3 injection pipe clamp.

  1. A225331
    Remove the 2 bolts and 2 No. 2 injection pipe clamps.

  1. A223451E01
    Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
    Text in Illustration 
    *a
    for Injector Side
    *b
    for Common Rail Side


10. REMOVE AIR CONNECTOR STAY

  1. A223452
    Remove the 3 bolts and air connector stay.


11. DISCONNECT ENGINE WIRE (for LHD)

  1. A225469
    Remove the 2 bolts.

  1. Detach the clamp and disconnect the engine wire.


12. DISCONNECT ENGINE WIRE (for RHD)

  1. A223453
    Remove the bolt and disconnect the engine wire.


13. REMOVE EGR VALVE BRACKET
  1. Remove the 2 nuts and EGR valve bracket.


14. REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY

  1. A223474
    Disconnect the 2 connectors from the electric EGR control valve and E-VRV.

  1. A223455
    Detach the wire harness clamp.

  1. A223475
    Disconnect the 5 vacuum hoses.

  1. Remove the bolt and gas filter together with the gas filter bracket.

  1. A223476
    Remove the 2 bolts and E-VRV bracket together with the EGR vacuum damper.


15. REMOVE NO. 2 INTAKE AIR CONNECTOR

  1. A223458
    Remove the 3 nuts, No. 2 intake air connector and gasket.


16. REMOVE INTAKE AIR CONNECTOR

  1. A223478
    Remove the 3 bolts, intake air connector and 2 gaskets.


17. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER

  1. A147220
    Disconnect the No. 3 vacuum transmitting hose from the No. 2 EGR valve.

  1. A223461
    Remove the bolt, 2 nuts, electric EGR control valve together with the No. 2 EGR valve and EGR cooler.

  1. Remove the gasket from the cylinder block.


18. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY

  1. A223462E01
    Remove the 2 bolts, electric EGR control valve and gasket.
    Text in Illustration 
    *A
    w/ EGR Cooler
    *B
    w/o EGR Cooler


19. REMOVE EGR VALVE ADAPTER

  1. A223463
    Using a 6 mm hexagon wrench, remove the 3 hexagon bolts, 3 plate washers, EGR valve adapter and gasket.


20. REMOVE NO. 2 EGR VALVE ASSEMBLY

  1. A223464
    Using a 5 mm hexagon wrench, remove the hexagon bolt, No. 2 EGR valve and gasket.


21. REMOVE EGR COOLER

A151135
← COMPONENTS (from Aug 2013)REMOVAL (from Aug 2014) →