2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B1443 Air Outlet Damper Control Servo Motor Circuit

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The damper servo sub-assembly (mode damper servo) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air outlet damper to any position, which controls the air outlet changes.

HINT:
Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.

DTC Code
DTC Detection Condition
Trouble Area
B1443
The air outlet damper position does not change when the air conditioning amplifier assembly operates the damper servo sub-assembly (mode damper servo).
  1. Damper servo sub-assembly (mode damper servo)
  2. Air conditioning harness assembly
  3. Air conditioning amplifier assembly

WIRING DIAGRAM

E180810E52

INSPECTION PROCEDURE


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1443 is not output
    A
    DTC B1443 is output
    B
    DTC B1443 and B1497 are output
    C



B
Go to step 2

C
GO TO B1497 (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

2. READ VALUE USING INTELLIGENT TESTER (MODE DAMPER SERVO)
  1. Use the Data List to check if the damper servo sub-assembly (mode damper servo) is functioning properly (Click here).

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Outlet Servo Pulse (D)
    Damper servo sub-assembly (mode damper servo) actual pulse / Min.: 0, Max.: 255
    15 (pulse): FACE
    41 (pulse): B/L
    65 or 73 (pulse): FOOT
    83 or 95 (pulse): F/D
    113 (pulse): DEF
    -
    Air Outlet Servo Actu Pulse (D)
    Damper servo sub-assembly (mode damper servo) actual pulse / Min.: 0, Max.: 255
    15 (pulse): FACE
    41 (pulse): B/L
    65 or 73 (pulse): FOOT
    83 or 95 (pulse): F/D
    113 (pulse): DEF
    -

    OK:
    The display is as specified in the normal condition column.

    Result 
    Result
    Proceed to
    OK (When troubleshooting according to the DTC)
    A
    OK (When troubleshooting according to Problem Symptoms Table
    B
    Both target pulse and actual pulse do not display
    C
    Target pulse displays normally, but actual pulse does not display
    D



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

D
Go to step 4
A


3. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1443 is not output.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)

4. CHECK DAMPER SERVO SUB-ASSEMBLY (MODE DAMPER SERVO)
  1. Replace the damper servo sub-assembly (mode damper servo) (Click here).

    HINT:
    Since the damper servo sub-assembly (mode damper servo) cannot be inspected while it is removed from the vehicle, replace the damper servo sub-assembly (mode damper servo) with a new or normally functioning one.

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1443 is not output.



NG
Go to step 5
OK

END (DAMPER SERVO SUB-ASSEMBLY [MODE DAMPER SERVO] IS FAULTY)

5. CHECK AIR CONDITIONING HARNESS ASSEMBLY
  1. Temporarily replace the air conditioning harness assembly with a new or normally functioning one (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1443 is not output.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

END (AIR CONDITIONING HARNESS ASSEMBLY IS FAULTY)


← B1443 Air Outlet Damper Control Servo Motor Circuit (Aug 2013 – Jul 2014)B1447 Air Mix Damper Control Servo Motor Circuit (Rear) (Aug 2013 – Jul 2014) →